Search results
-
350 to 454
Towing my 5k lbs enclosed trailer, my 700 rarely gets above 150 deg. They can be made to take some abuse- Derick C.
- Post #21
- Forum: Engine & Performance
-
350 to 454
My suburban is 90 and the 454 came out of a 91 1 ton truck The trans has the beast sunshell, hd bands and clutches, corvette servo, new planetary set, new main shaft, and shift kit, there could be more but I don't know transmissions that well.- Derick C.
- Post #17
- Forum: Engine & Performance
-
350 to 454
Mine runs just fine with the 350 computer and the built 700r4. I used all the sensors from the 350 so I didn't need to change any pigtails- Derick C.
- Post #13
- Forum: Engine & Performance
-
383 Vortec/TBI Build Thread
Still using the mostly stock tbi, I change the spring in the fuel pressure regulator to bump up the pressure, put in a wide band gauge and have been running fine. A chip might help but air fuel ratio is fine so I haven't worried about it.- Derick C.
- Post #52
- Forum: Engine & Performance
-
383 Vortec/TBI Build Thread
30 over, procomp aluminum heads, 202/160, stock rockers for now, I want to try a set of 1.6's Don't remember the dish on the pistons but it is 9.5:1 CR- Derick C.
- Post #48
- Forum: Engine & Performance
-
383 Vortec/TBI Build Thread
I am running a stock vortec cam in my 92 GMC. No complaints- Derick C.
- Post #46
- Forum: Engine & Performance
-
-
Short Girl, Tall Truck
Welcome. I need to find one of those winch bumpers- Derick C.
- Post #18
- Forum: Introduction
-
700R4 cooler for a 4L80E trans?
I use this same trans cooler on both my trucks. Made my own lines, the feed line goes to the radiator then to the cooler before returning to the trans.- Derick C.
- Post #6
- Forum: Automatic Transmission
-
Hello from Kansas
Welcome to the forum. Nice truck. He only changed the oil every 150K? Maybe you meant 15k- Derick C.
- Post #7
- Forum: Introduction
-
-
Hello from the PNW
I have a pic thread http://www.gmsquarebody.com/threads/my-new-1990-burb.11462/- Derick C.
- Post #11
- Forum: Introduction
-
-
-
New member in NE Washington
Welcome... Do I see a red square in the back?- Derick C.
- Post #8
- Forum: Introduction
-
New Member NW Oklahoma
Welcome :cheers: Pics are a must :popcorn:- Derick C.
- Post #5
- Forum: Introduction
-
Newbie from Idaho...
welcome. those are bad ass trucks, to bad most people buy them for the axles and the rest gets parted out.- Derick C.
- Post #10
- Forum: Introduction
-
Picked up my '78 C10 today
Nice looking truck. :cheers: Time for a Seattle are square body get together? LOL- Derick C.
- Post #11
- Forum: Introduction
-
Newbie from Washington state
Welcome Was that blue one on CL not to long ago?- Derick C.
- Post #9
- Forum: Introduction
-
New guy in Seattle, WA
Welcome. Not a bad looking truck at all.- Derick C.
- Post #7
- Forum: Introduction
-
Hello From Arkansas
Welcome. Start a build thread. No more upside down pics though LOL- Derick C.
- Post #17
- Forum: Introduction
-
14 Bolt SF 8 lug to 6 lug Conversion
I just beveled the rotors a little bit with a grinder to get mine on.- Derick C.
- Post #16
- Forum: Differential & Driveline
-
14 Bolt SF 8 lug to 6 lug Conversion
I have a SF from another suburban- Derick C.
- Post #13
- Forum: Differential & Driveline
-
14 Bolt SF 8 lug to 6 lug Conversion
I will be doing a similar axle swap but I want to go 8 lug.- Derick C.
- Post #11
- Forum: Differential & Driveline
-
