Homemade and modified tool thread

[Nasty-LSX]

Tig arm prop.
Part 2 pops up at the end.

xc_hide_links_from_guests_guests_error_hide_media

Trans install tool. My very first video.

xc_hide_links_from_guests_guests_error_hide_media

 

[Ricko1966]

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

Been setting toe this way for decades.longer angle and bigger cans for bigger cars. That's an old pic I now use longer angle on everything it's more accurate thought about drilling holes so bolts could be run through the angle to locate on the wheel instead of the tire but haven't.Other side is same set up with tapes clothes pinned to angle. Paint cans work good on 4wd stuff.

 

[eskimomann209]

I’m a cheap bastard and wanted a stand up ashtray for the cigars we smoke.
Had a couple drums laying around and figured **** it. I’ll make one.
The poor Oliva Serie V that got naked was due to a female smoking it with very long nails.
She managed to peel the wrapper clean off LOL.
Other one was a My father line.
Some leftover fish rock and sand was the filler material used.

You must be registered for see images attach

 

[wanderinthru]

Couple elevators built for a well man.

You must be registered for see images attach

 

[wanderinthru]

I’m a cheap bastard and wanted a stand up ashtray for the cigars we smoke.
Had a couple drums laying around and figured **** it. I’ll make one.
The poor Oliva Serie V that got naked was due to a female smoking it with very long nails.
She managed to peel the wrapper clean off LOL.
Other one was a My father line.
Some leftover fish rock and sand was the filler material used.

You must be registered for see images attach

Not going to ask, long nails, female, naked and both cigars are in the tray.....

Nice ash tray, thats cool!!

 

[eskimomann209]

Not going to ask, long nails, female, naked and both cigars are in the tray.....

Nice ash tray, thats cool!!

Haha thanks.
I should have built a middle “shelf” area for the lighters and cutters ...

 

[CalSgt]

Alignment toe tool I made for my Jeep, then adapted it to work on dads GMT400 & my K10

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[89Suburban]

Okay, not mine. I have a press and my bearing separator press, But I like this probably will make one for ball joints and U joints. Yes I have the big c clamp service press but think this will be more useful.

You must be registered for see images attach

I need something like that to crush my beer cans.

 

[CalSgt]

Homemade pinion yoke anchor, holds the yoke steady while you collapse the crush sleeve to set pinion preload. Ultimately turns the floor (or shop bench) into a deadman while you apply the foot Lb's

https://www.gmsquarebody.com/threads/80-k-10-squircle-build.34732/

You must be registered for see images attach

 

[CRM]

This is my hack valve lash adjustment tool.

You must be registered for see images attach

 

[CalSgt]

Custom bandsaw for making perfect cuts in exhaust U bends

 

[CalSgt]

Custom bandsaw for making perfect cuts in exhaust U bends

Couldn't get the photos to load last night

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[AyWoSch Motors]

Made this one a while back.

Anyone guess what it's for?

You must be registered for see images attach

 

[78C10BigTen]

Made this one a while back.

Anyone guess what it's for?

You must be registered for see images attach

Jumping "shorting" the 2 terminals on a pre obd gm car?!

 

[78C10BigTen]

Made this one a while back.

Anyone guess what it's for?

You must be registered for see images attach

Otherwise a "fish can key" for opening old school door knobs? Lol