1984 K10 Steering Column question.

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Shawn Wheeler

Junior Member
Joined
Feb 10, 2019
Posts
22
Reaction score
33
Location
Arizona
First Name
Shawn
Truck Year
1984
Truck Model
K10
Engine Size
305
1984 K10 Steering Column question.

Tilt steering column. The tilt works fine. However, I recently noticed the wheel will move right to left and up and down if I try to make that happen.

This could have recently started, or I recently noticed now that I am trying to fix all the little things after 34 years of ownership.

Also, the ignition switch is getting tough to remove the key.

Could these be interrelated?
I watched the video or changing the ignition switch, looks like quite a bit of stuff for me to mess up.
Does the column need to be rebuilt?
 

CalSgt

Full Access Member
Joined
Oct 3, 2021
Posts
1,699
Reaction score
3,761
Location
CA
First Name
Casey
Truck Year
1980
Truck Model
Chevy K-10 Custom Deluxe
Engine Size
350
Not sure if the difficult key removal is related to the wobbly column.

These four torx headed bolts loosen up over time causing the column to wobble. It’s quit the job breaking the column down this far but, if you remove the wheel, lock plate, and turn signal switch you can get to two of them IIRC. It couldn’t hurt to refurbish the upper portion of the column but do some research and be prepared for a change.
You must be registered for see images attach


You may try lubricating the lock cylinder with graphite or some other dry lube to get you by.
 

Dleslie212

Full Access Member
Joined
Sep 2, 2019
Posts
243
Reaction score
149
Location
Phoenix
First Name
Dustin
Truck Year
1977
Truck Model
K10
Engine Size
5.7L 350
Cal is right, it's those 4 bolts loosening up. I completely rebuilt my column about a year ago, including all new bearings and any part that was still available for purchase. It started by wanting to tighten up the play in the wheel. If you get far enough into it to tighten those bolts up, make sure you use some Loc Tite to keep them from ever loosening again
 

Shawn Wheeler

Junior Member
Joined
Feb 10, 2019
Posts
22
Reaction score
33
Location
Arizona
First Name
Shawn
Truck Year
1984
Truck Model
K10
Engine Size
305
Thank you all. I have a new question. After reading and watching the videos, I chickened out and paid to have the bolts fixed.

The mechanic tightened the bolt noted above. He also said the upper section has worn out bearings and the column needed to be replaced.

Can the upper section be rebuilt?

If it can't be rebuilt. Can an automatic column be converted into manual version?
 

SquareRoot

Full Access Member
Joined
Mar 18, 2017
Posts
4,192
Reaction score
8,030
Location
Arizona
First Name
Mike
Truck Year
85
Truck Model
K20
Engine Size
350
Thank you all. I have a new question. After reading and watching the videos, I chickened out and paid to have the bolts fixed.

The mechanic tightened the bolt noted above. He also said the upper section has worn out bearings and the column needed to be replaced.

Can the upper section be rebuilt?

If it can't be rebuilt. Can an automatic column be converted into manual version?
Are you implying you have a manual tilt column?
 

mattsk8

Full Access Member
Joined
Jun 5, 2024
Posts
172
Reaction score
448
Location
Michigan
First Name
Matt
Truck Year
1986
Truck Model
K20
Engine Size
350
Not sure about the squares, but I have seen a lot of GM cars that had automatic columns used in manuals, I have a 69 Cutlass with one (just pop the shift lever out of it)... you might even be able to put your manual section out of your old column in the auto so you don't have the shift lever part, but that might also be the part of your column that has the bad bearings, I'm not sure. It can be annoying because sometimes you'll inadvertently bump the column shifter part, and either can't shut the key all the way off or won't be able to start it. Then it takes a minute to figure out what's wrong, until you remember you have an auto column and bumped that, and just need to spin it back to park.

Edit: Thinking more this won't work on yours because of how the automatic steering columns lock when it's in park. Not sure how it works on my Cutlass, maybe that column doesn't lock at all.
 
Last edited:

TexasMan81

Junior Member
Joined
Feb 2, 2024
Posts
9
Reaction score
7
Location
Cumby, Texas
First Name
Kalvin
Truck Year
1989
Truck Model
K1500 Suburban
Engine Size
350
Thank you all. I have a new question. After reading and watching the videos, I chickened out and paid to have the bolts fixed.

The mechanic tightened the bolt noted above. He also said the upper section has worn out bearings and the column needed to be replaced.

Can the upper section be rebuilt?

If it can't be rebuilt. Can an automatic column be converted into manual version?
look at part # 32 here. I have done this personally. It's not that hard if you take your time and be easy on the parts. Don't force anything. https://www.lmctruck.com/steering/steering-column-parts/cc-1973-87-steering-components
 

Latest posts

Forum statistics

Threads
44,157
Posts
950,599
Members
36,273
Latest member
dannyphx
Top