Search results
-
-
A couple fuel related questions
That right tank probably looks like this: http://www.gmsquarebody.com/forum/showthread.php?t=6146&highlight=tank see post #6- GTME94
- Post #6
- Forum: Carb Fuel Systems
-
Anything on Wheels Show-Michigan
That's not too far from where my square lives in Holland. I'll have to see if we'll be over there that weekend. -
Michigan Man
Welcome, another Michigander here. We're bicoastal so we go past Lansing frequently.- GTME94
- Post #6
- Forum: Introduction
-
What have you done to your square lately??
That's a great idea! I'll try that next time I'm over at my truck. -
What have you done to your square lately??
Adjusted my choke some more. It was idling too high and the choke wasn't pulling off. Now it seems good. Also got some vacuum hose and a heat stove pipe and hooked up the exhaust heat flapper door in the air cleaner. The flapper door works when cold, didn't get a chance to get it fully... -
-
new from michigan
Welcome, Metro Detroit here but my square lives at our second place in Holland.- GTME94
- Post #12
- Forum: Introduction
-
Riddler differential cover
Yeah, I can see it from that perspective. Pretty cool cover. I can't imagine making a 14B any heavier though. My whole axle must weigh a ton with the heavy duty drums.- GTME94
- Post #8
- Forum: Differential & Driveline
-
Riddler differential cover
That sounds like a worthless test unless your needing a getaway vehicle and your worried about getting shot at and losing your gear lube.- GTME94
- Post #6
- Forum: Differential & Driveline
-
Poor Man Valve Job
When I was a kid we bought a 66 Falcon with a straight six. The head had been off for some reason. Helped my dad hand lap the valves. That motor lasted forever. It was my brothers first car for a couple years, my dad drove it for 10 or so years and then he sold it and they drove it for at...- GTME94
- Post #18
- Forum: Engine & Performance
-
New Member From Oklahoma
I'm sorta late to the party but Welcome. Spent a few years in Jay, OK growing up.- GTME94
- Post #13
- Forum: Introduction
-
Another new member from Oklahoma
Welcome. Growing up we lived in Jay, Ok. for a while.- GTME94
- Post #6
- Forum: Introduction
-
TH400 Kick down Switch Problem
Do'h, I didn't even look to see that it's a sticky. And it was SlickGTP that helped out.- GTME94
- Post #4
- Forum: Automatic Transmission
-
TH400 Kick down Switch Problem
There's a thread on here somewhere about this, I had the same problem. Foamy Pirate helped out, it is an adjustable switch. Push it down towards the pedal. It will make a scratchy, crackly sound as it moves. Then fully press the gas pedal. It might have to re-adjust witht he same sound but...- GTME94
- Post #2
- Forum: Automatic Transmission
-
Touch up on steel wheels
HR, I have the same wheels and they were rusty too. They got sanded and painted with "chrome" paint. They look good from 10 feet away and ok up close. I'd say it was worth a can or two of spray bomb. Hell of a lot cheaper than new wheels. We'll see how it holds up over time. They've been...- GTME94
- Post #9
- Forum: Wheels and Tires
-
Oil pressure fluctuating
What weight oil are you running? At -20 the oil starts to get thick like pudding. But also sounds like you might have a pretty loose engine that runs low pressure when warm. Since it's supposed to stay cold I'd look for oil with a big weight spread to not be too viscous when cold but help...- GTME94
- Post #3
- Forum: Engine & Performance
-
Bugwash always on
I think the wire is for cruise only. The wiper switch is inside the column. The arm is just a lever to move the switch.- GTME94
- Post #2
- Forum: Electrical & Audio
-
1987 Silverado Wipers Slow
That is exactly how my wire is. Works fine. I don't care how it looks, it was too much trouble to fish it thru.- GTME94
- Post #20
- Forum: Electrical & Audio
-
NO OIL pressure
Are you saying you get oil pressure with the priming tool after the head swap but not when assembled with a real distributor? If that's the case it seems like your dizzy isn't engaging the oil pump drive.- GTME94
- Post #2
- Forum: Engine & Performance
-
Ignition problem- New parts, no spark- 454 HEI
That's how my '86 454 is. I'm not sure it even has EGR, or maybe it was removed before I got it. I removed the AIR and evap.- GTME94
- Post #10
- Forum: Tech Discussion
-
What have you done to your square lately??
Figured out some of my underhood wiring. Put a jumper on the terminals of my oil pressure switch to make the choke light go off and hoped it would help the choke pull off. It is still stuck on with too high of an idle but I didn't have time to adjust it. I will also put in the proper oil... -
Looking for best place to tie in electric choke
I've been doing a little research to get my choke right. I can't tell you the right place to tie into but can give a little advice. Mine has factory wiring tied into an oil pressure switch. I just jumpered across the terminals for now but the oil pressure switch is a good idea. With the...- GTME94
- Post #2
- Forum: Carb Fuel Systems
-
Wiper Arms Modification?
Hey Paw Paw, could you switch the square hub onto the 400 arm? Is the shaft same diameter? The 400 arm is wider, might need a spacer or washers to take up the space between the hub and arm. Would have to make a new shaft. -
Best reupholstery kit for bench seat
Mine is from LMC, I'm happy with it. My truck doesn't get used much so I can't say how durable it will be but the quality seems good. My dad restored my truck for me and installed so I don't know how difficult it was.
