Cyrillious
Full Access Member
- Joined
- Aug 25, 2022
- Posts
- 139
- Reaction score
- 111
- Location
- Toronto
- First Name
- Cyril
- Truck Year
- 1980
- Truck Model
- K10 Suburban
- Engine Size
- 350
6 lug is mine. K10
Rims won't fit on rear with drums.
- Thread starter Cyrillious
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
Cyrillious
Full Access Member
- Joined
- Aug 25, 2022
- Posts
- 139
- Reaction score
- 111
- Location
- Toronto
- First Name
- Cyril
- Truck Year
- 1980
- Truck Model
- K10 Suburban
- Engine Size
- 350
I wonder if a drum like this would work? Or cheaper to have my surface lip machined down?
Attachments
Ricko1966
Full Access Member
- Joined
- Apr 11, 2017
- Posts
- 5,446
- Reaction score
- 8,683
- Location
- kansas
- First Name
- Rick
- Truck Year
- 1975
- Truck Model
- c20
- Engine Size
- 350
I need to see both sides of this rim and from a little further back. To me in that Pic that looks like it's supposed to be the outside,not touching the drum.
Last edited:
mlsceo
Full Access Member
- Joined
- Dec 29, 2022
- Posts
- 399
- Reaction score
- 1,191
- Location
- Kingsburg California
- First Name
- Manuel
- Truck Year
- 1977
- Truck Model
- c10
- Engine Size
- 350
I was referring to the outer edges of the drum.
mlsceo
Full Access Member
- Joined
- Dec 29, 2022
- Posts
- 399
- Reaction score
- 1,191
- Location
- Kingsburg California
- First Name
- Manuel
- Truck Year
- 1977
- Truck Model
- c10
- Engine Size
- 350
Take a wheel and a drum to your local fab shop. Let them have a look. Take one of your factory wheels as well for comparison. I won't cost you anything to have them look at it and you do not want to machine down your factory drums. Buying different drums without test fitting will very likely reveal the same issue because it's the aftermarket wheel center that is different from the factory wheel center.
Last edited:
mlsceo
Full Access Member
- Joined
- Dec 29, 2022
- Posts
- 399
- Reaction score
- 1,191
- Location
- Kingsburg California
- First Name
- Manuel
- Truck Year
- 1977
- Truck Model
- c10
- Engine Size
- 350
This drum appears to have the same lip, looks like the two notches are the only difference.
- Joined
- Aug 3, 2010
- Posts
- 30,439
- Reaction score
- 28,345
- Location
- Usually not in Ohio
- First Name
- Andy
- Truck Year
- '77, '78, '79, '84, '88
- Truck Model
- K5 thru K30
- Engine Size
- 350-454
I believe the notches are there just for balancing.
mlsceo
Full Access Member
- Joined
- Dec 29, 2022
- Posts
- 399
- Reaction score
- 1,191
- Location
- Kingsburg California
- First Name
- Manuel
- Truck Year
- 1977
- Truck Model
- c10
- Engine Size
- 350
OP, how did the fresh paint around all six wheel stud holes get so dinged up? What surface did that mounting face contact? The chipped paint on the edges of the wheel center openings are exactly what I experienced, But the mounting surface of the wheel never contacted the drum until after I trimmed back those lips between the wheel center welds.
AuroraGirl
Full Access Member
- Joined
- Sep 8, 2019
- Posts
- 9,693
- Reaction score
- 6,869
- Location
- Northern Wisconsin
- First Name
- Taylor
- Truck Year
- 1978, 1980
- Truck Model
- K10, K25
- Engine Size
- 400(?), 350
the weights should be balanced betwene the other side, take 2 of the outer ones and put them on the inside (or other side) of the rim, across from them, so they arent so far away.
And if that is what a balancer asked for, the tire needs to be match-mounted no the wheel, the low point of the wheel (usually valve stem hole but not always) to the corresponding paint mark on the new tire, if not a new tire, then just rotate the tire a decent amount from where it is now then try to rebalance, if still bad, try a third spot
- Joined
- Aug 3, 2010
- Posts
- 30,439
- Reaction score
- 28,345
- Location
- Usually not in Ohio
- First Name
- Andy
- Truck Year
- '77, '78, '79, '84, '88
- Truck Model
- K5 thru K30
- Engine Size
- 350-454
Normally yes, weights on both sides. But some goofballs such as myself don't like weights on the outside. Not just because of looks, but also damage to the exposed rim surface.
But, that is a lot of weight for just a 33" radial. I'm guessing a combo of a heavy sided tire and a rim that doesn't spin very true.
mlsceo
Full Access Member
- Joined
- Dec 29, 2022
- Posts
- 399
- Reaction score
- 1,191
- Location
- Kingsburg California
- First Name
- Manuel
- Truck Year
- 1977
- Truck Model
- c10
- Engine Size
- 350
I repeat the question. Did you take a hammer to the raised areas around the stud holes thinking they were causing the issue?
Last edited:
Redfish
Full Access Member
- Joined
- Nov 6, 2021
- Posts
- 2,648
- Reaction score
- 14,265
- Location
- Prairieville, LA
- First Name
- Andrew
- Truck Year
- 1987
- Truck Model
- V1500
- Engine Size
- 350/5.7
I am not trying to make this worse for you but I am running 33x12.50 mud grips and they don't need that much weight. If you have that much lead on that wheel something is wrong.
- Joined
- Aug 3, 2010
- Posts
- 30,439
- Reaction score
- 28,345
- Location
- Usually not in Ohio
- First Name
- Andy
- Truck Year
- '77, '78, '79, '84, '88
- Truck Model
- K5 thru K30
- Engine Size
- 350-454
Likely just from contact on the wheel balancer hub. There's also evidence of a center cone used to hold the wheel on the balancer.
AuroraGirl
Full Access Member
- Joined
- Sep 8, 2019
- Posts
- 9,693
- Reaction score
- 6,869
- Location
- Northern Wisconsin
- First Name
- Taylor
- Truck Year
- 1978, 1980
- Truck Model
- K10, K25
- Engine Size
- 400(?), 350
a wheel thats lug centric should use a lug centric mounting adapter and not a cone, i know its not nearly common because a cone is faster for people, btu that would be more accurate.
and the weight problem you brought up about the outside,you can remedy that with pound on weights on the inside but use stick on weights as close to the outside , but in the outer part of the wheel by the brakes , across from the pounded in ones.
And like I said, match mounting is a good way to get the part needing "s omuch weight" to another place on the wheel where they can balance eachother some what
Bennyt
Full Access Member
- Joined
- May 17, 2019
- Posts
- 1,201
- Reaction score
- 1,850
- Location
- Surprise
- First Name
- Ben
- Truck Year
- 1977
- Truck Model
- C10
- Engine Size
- 350
Can't help with the rim issue but would definitely try rotating the tire to see if that helps reduce the weights or switch to airsoft beads.
Similar threads
