What have you done to your square lately??

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

nvrenuf

Full Access Member
Joined
Jul 30, 2010
Posts
1,940
Reaction score
2,424
Location
Mobile, Al.
First Name
John
Truck Year
1991
Truck Model
K5
Engine Size
454
Fuggin A Lovely !!! What is it??? Huh.. What is it, what is it ???

LOL! I've got to update my build thread.

Here's the quick list (some new, some reused) -

454 (4 bolt main), hypereutectic pistons (9.4:1 comp), '781 heads, Comp Cam roller cam (.566 lift, 215 duration @ .050 on 110° lobe centerline)

Give me a few minutes and I'll put a more detailed description in my build thread.
 

smurph20

Full Access Member
Joined
Jul 13, 2011
Posts
2,063
Reaction score
23
Location
Clyde, Arkansas 72717
First Name
Brad
Truck Year
1986
Truck Model
K20
Engine Size
350/SM465/NP208/4.10's
Well i did all new powef steering lines yesterday along with putting some mufflers on it so now its not sounding like a racecar going to work. On my next days off im going to be dropping the left tank and swapping it for a good one with a new sending unit and putting a good tank back on the right side with a new sending unit and putting all new rubber lines on it since the hardlines still look good with no rust on them. I also put a new fuel tank switch on the dash yesterday.
 

c10lo

Junior Member
Joined
Mar 25, 2011
Posts
6
Reaction score
0
Location
maryland
First Name
slik
Truck Year
1977
Truck Model
c10
Engine Size
454
Gotta get back on that body work so I can get it in the paint shop.
 

8T6K5

Full Access Member
Joined
Jun 22, 2012
Posts
1,128
Reaction score
121
Location
AZ
First Name
Jerry
Truck Year
1986
Truck Model
K5
Engine Size
L98 350 TPI
F/R brakes, although the job isnt quite complete yet....new (reman) calipers enroute to finish.
 

WVscottsdale

Full Access Member
Joined
Aug 4, 2012
Posts
101
Reaction score
14
Location
West by God Virginia
First Name
Daniel
Truck Year
1977
Truck Model
Scottsdale K10
Engine Size
350 bored .040 over
1/2 ton to 3/4 ton axle swap with 4 inch lift and 35x12.50 tires
 

HotRodPC

Administrator
Staff member
Admin
Joined
Aug 29, 2010
Posts
47,128
Reaction score
9,299
Location
OKC, OK
First Name
HotRod
Truck Year
85 K20 LWB
Truck Model
Silverado
Engine Size
454 - Turbo 400 - 3.73
1/2 ton to 3/4 ton axle swap with 4 inch lift and 35x12.50 tires

Any before and after pics Daniel??? I'll be the exact same thing to an 85. Are you swapping to 56in 3/4 ton springs too?
 

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
30,407
Reaction score
28,202
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
Put a new (well, a good spare) ignition lock cylinder in the 4x4 Burb this morning. The old one crapped out and you had to turn the truck off with vice grips.
 

smurph20

Full Access Member
Joined
Jul 13, 2011
Posts
2,063
Reaction score
23
Location
Clyde, Arkansas 72717
First Name
Brad
Truck Year
1986
Truck Model
K20
Engine Size
350/SM465/NP208/4.10's
Be puttin my right tank back in with new sending unit and putting all new hoses in with today along with changing out the grill and had my buddy weld up my new mufflers and some extention pipe last night to get it to end under the bed instead of the cab A LOT quieter.
 

GreaseDog

Full Access Member
Joined
Aug 8, 2010
Posts
1,189
Reaction score
36
Location
Elkhart, IN
First Name
Jeremy
Truck Year
1977 K20
Truck Model
1980 K2500
Engine Size
350
I took the plow bracket off of my 80 friday night, along with the bumper brackets, and the crusty old exhaust manifolds. Next up its the 350/465/205, then I'll put a mock up 350 back in it with the 80e/241... Ford dana 44 will go in, then start fabricating body mounts...
 

DoubleDingo

Full Access Member
Joined
Jul 3, 2012
Posts
11,228
Reaction score
17,070
Location
Right where I am
First Name
Bagoomba
Truck Year
1981
Truck Model
81-C20 Silverado Camper Special-TH400-4.10s
Engine Size
Carb'ed Vortec 350
(Today)...Fixed a fuel leak at the carb, sprayed the carb clean, replaced the air filter, partially cleaned the inside of the cab; (Last week) packed wheel bearings, put good wheels and tires on...
 

WVscottsdale

Full Access Member
Joined
Aug 4, 2012
Posts
101
Reaction score
14
Location
West by God Virginia
First Name
Daniel
Truck Year
1977
Truck Model
Scottsdale K10
Engine Size
350 bored .040 over
Any before and after pics Daniel??? I'll be the exact same thing to an 85. Are you swapping to 56in 3/4 ton springs too?
no i kept the springs that were on the old truck they look like a 1 ton spring pack but i cant remeber the length yeah pics are on my profile i have also took out the full-time transfer case for a NP205 transfer case the swap out was easy for the most part but now i need a conversion u joint and shorten my front drive shaft
 

89Suburban

Supporting Member
Supporting Member
Joined
Dec 7, 2010
Posts
24,758
Reaction score
6,591
Location
Southeast PA
First Name
Paw Paw
Truck Year
2007
Truck Model
Chevrolet Tahoe LT
Engine Size
5.3, 4WD
I drove it until the engine light came on, lol!! :shitsweak:
 

foamypirate

Full Access Member
Joined
Jul 30, 2010
Posts
3,302
Reaction score
456
Location
Central TX
First Name
Jake (Mr. Wilson)
Truck Year
1980
Truck Model
El Camino, baby!
Engine Size
5.3L/4L60E
Tied up all the loose grounds for the ALDL / Park Neutral Switch inside the cab. Also got the straight six out of the truck, and getting ready to put the TBI 305 in. Did some other stuff I don't remember too.
 

DoubleDingo

Full Access Member
Joined
Jul 3, 2012
Posts
11,228
Reaction score
17,070
Location
Right where I am
First Name
Bagoomba
Truck Year
1981
Truck Model
81-C20 Silverado Camper Special-TH400-4.10s
Engine Size
Carb'ed Vortec 350
Tied up all the loose grounds for the ALDL / Park Neutral Switch inside the cab. Also got the straight six out of the truck, and getting ready to put the TBI 305 in. Did some other stuff I don't remember too.

Not sure what the smog requirements are in Texas, but if you have to smog that truck, don't forget to put a V-8 canister in the truck and whatever else that may be required for that year truck.
 

Old77

Administrator
Staff member
Admin
Joined
Aug 19, 2010
Posts
28,451
Reaction score
9,404
Location
Kansas City, Mo
First Name
Jacob
Truck Year
1977/1990/1991
Truck Model
C10 longbed/R1500 Burb/R3500 Dually
Engine Size
350/350/454
took the boys and I out for a spin on Saturday morning for a little while. They were beyond excited when I asked them if they wanted to go.

It was Saturday morning and I'd been thinking about it since Friday afternoon. We'd just eaten breakfast and as usual they start asking what we're going to do today because they always want to keep moving and doing stuff. Anyhoot, I said "oh I don't know. Probably nothing" and I went off to the bathroom as they start to whine :lol: I come back and the oldest one had gotten dressed already and I say everyone who is dressed gets to go for a truck ride let's go!! :D I did this just teasing just to see what my 3 year old would do. He leaped off the couch and ran to his room as quick as he could. 10 seconds later he brought back shorts and a t-shirt to help him get dressed :happy175:

They really had a good time and loved it. We mostly drove around town just cruisin but at one point we got on the highway for about 2 or 3 miles. As I was merging onto the highway I punched the gas, the truck roared and I looked over and my 5 year old was beaming from ear to ear with enjoyment. It was pretty funny. I have a feeling he's going to get a few speeding tickets when he gets older. I hope he has a good job to pay for them :D
 

Latest posts

Forum statistics

Threads
44,082
Posts
949,037
Members
36,162
Latest member
jbahena95
Top