Search results
-
5/6 static dropped dually, complete.... sorta
that is a very sweet truck .I dig the 22's on it and the stance I would love to do that to my :badidea: dodge dually :sorry: but I do have 2 square body trucks as well and hell they are both belly scrapers :party36: so please do a build thread and show the wheel adaptors that you used I for one...- 74propu
- Post #22
- Forum: Lowered & Street Systems
-
tilt swap
yep it is backwards and upside down just flip the plugs over and they will plug right in I just did the tilt swap and ran in to this- 74propu
- Post #3
- Forum: Tech Discussion
-
Adding a Second Tank to an Original Dual Tank Truck
inside the 87 tank there is a sump that the fuel pump sits in so it doesn't lose presser when the tank is about empty when brakeing and tacking off from a stop . it is called a baffle other then that the tanks are the same- 74propu
- Post #7
- Forum: Tech Discussion
-
Adding a Second Tank to an Original Dual Tank Truck
no the tanks out of the 85 will not work the tbi needs to fuel pump in the tank where the 85 had a carb and the pump on the engine look and see if the crossover lines are still on the frame under the cab at the crossmember and see if thay are still hooked to the fuel valve if they are look on...- 74propu
- Post #5
- Forum: Tech Discussion
-
Cab swap legality
my dodge 3500 has a Kansas recover title it was stolen and recovered so Kansas did a new title with the same vin# that it had before and Florida didn't have a problem with it as long as they got there inpact fee and new title cost me $400 to reg that truck the 1st time- 74propu
- Post #26
- Forum: Retro-Fit & Aftermarket Accessories
-
Gen V 454 Swap into 1986 K10?
I am doing the same swap into my 1986 gen v with a 4l80e . Jason @ warr performance hooked me up with a stand alone harness,ecu and vssb for like $430 the harness is well marked where they all go it has been plug and play . if the ecu has been in the water it is trash you will need a new one ...- 74propu
- Post #6
- Forum: Engine & Performance
-
big block compressor brackets
thank you smooth but the small block brackets are not the same as the big block how and where they bolt to the head is not the same . I have found out that these brackets were only made for 2 years . in 84 they used the a6 compressor then 85-86 the r4 v-belt compressor in 87 went to r4... -
tank selctor valve
thank you very much chengny I have been looking for info on this valve and the 2 web sits you gave helped me I ordered the kit from ase:cheers:- 74propu
- Post #6
- Forum: TBI & EFI Conversions
-
big block compressor brackets
ok i will try this pic it is short and big around -
big block compressor brackets
I need a set of r-4 a/c compressor brackets for the driver side of a big block with a long water pump . or if there is someone that knows of a bracket that will work let me know . I just don't want to change everything up and have a 508 compressor and lines on it I am trying to keep it all GM... -
Squarebody Down! HELP - Member Roadside Assistance Volunteer Map
34420 mid state florida if I can't fix it it aint broke it needs replaced -
Free: auto shift indicator + delco knobs
why thank you Bucket you are a gentleman and scholar . and to pass it on I have 2 of the th350/400 3 speed shift indicator I will pass on to some one just pay the shipping :cheers: -
bad luck with both my squares at the time!! burning up HEI module.. WHY?
dose the dizzy shaft have any movement (slop) in it ??? if so the pick up can get damaged and short out that is a bad problem with the efi dizzys- 74propu
- Post #6
- Forum: Engine & Performance
-
1986 roll over oil switch
ok that make sense the choke was not hooked up and that wire was just laying on the eng . so can I just do away with the 3 wire oil sender don't need a choke on a BB tbi engine- 74propu
- Post #3
- Forum: Tech Discussion
-
1986 roll over oil switch
in 1986 did chevy put a roll over oil switch in c10 the v 6 I pulled out had 2 oil psi sensors in it 1 has one green wire to it the other has 3 wires to it pink ,blue hard wired into the harness the other is green and has a conector on it where dose that wire go it was not hooked up when I...- 74propu
- Thread
- Replies: 2
- Forum: Tech Discussion
-
Belltech 4/6 installed
I just put the same flip kit in my 86 and the axel tube would not seat all the way into the bracket it would hit the sides of the bracket first that keep the axel from going all the way in to the bottom of the bracket. I used a 4in grinder to open the sides more so the axel could go all the way...- 74propu
- Post #47
- Forum: Lowered & Street Systems
-
What have you done to your square lately??
flip kit and bed change took of the bed and did a 6 in flip and put the dually bed on and I like it -
85-86 ECM for california truck
I have one out of my 86 c10 had a 4.3 v6 and th375 trans cant read the numbers off it but it did have a 4 barrel on it. if it will help it is yours for the shipping -
Steering column
:shrug:i have a astro van column in my 1974 c10 short box -
Gear Ratio by Tachometer
to find out what gear is in the rear end on the passanger side axel tube on top about 6 in from the 3rd member is a code stamped in the tube clean it off so you can read it then Retroc10sport has a post with the codes. GM Square Body - 1973 - 1987 GM Truck Forum > '73 - '87 GM Truck...- 74propu
- Post #5
- Forum: Differential & Driveline
-
Ghost in the Machine
in 1991 I worked for a school bus comp in Kansas city and we ran about 600 buses and I learned 1 thing very fast if the bus would start cold but had to pump the gas to keep it running till I could get it in the shop and if it died after it wormed a little and wouldn't start till it cooled off ...- 74propu
- Post #3
- Forum: Engine & Performance
-
TH 400 won't go into gear after sitting.
I had a 400 that did the same thing found out the filter was lose in the valve body put a bigger o ring on the filter and it worked fine after that . get a new filter and go to a hydraulic shop and get a thicker o ring for it and see if that will fix it- 74propu
- Post #5
- Forum: Automatic Transmission
-
Tailgate molding/cover/trim
or I have a tail gate band off my truck I will take $75 and shipping it has a few dings but can be taped out -
Parts...Parts...Parts...
shawn I got my package from you today thank you very much:cheers:
