Search results
-
GM Square Body swb 4x4 Build & Upgrades
Usually, the R&P will have the numbers on the ring gear. Like this... 14:43 or a 3.08 gear ratio. Yours could be 10:41 for 4.10 ratio or 11:41 for a 3.73 ratio.- dvdswan
- Post #9
- Forum: Introduction
-
84 K10 Factory A/C??
Yep, aftermarket AC. Factory AC with have the unit that looks like this in the engine compartment. The factory HVAC selector will also have settings for MAX, Bi-Level, and vent. -
-
-
New to Chevy trucks I picked a good place to start ?
Looks like a keeper. You should have the other thread deleted that you introduced yourself on.- dvdswan
- Post #4
- Forum: Introduction
-
New to Chevy trucks I picked a good place to start ?
Welcome to the site. Any pics of said K20?- dvdswan
- Post #3
- Forum: Introduction
-
Engine shut off while driving my '90 Suburban. Sup with that?
How much gas did you have in the tank? The level of fuel effects how hot the FP gets. Being in the desert, summertime temps were a good culprit to killing the FP on a low tank of gas.- dvdswan
- Post #12
- Forum: Engine & Performance
-
-
New guy here : 86 K10
Welcome to the site. Glad to hear it's back in your hands.- dvdswan
- Post #20
- Forum: Introduction
-
-
-
Wiring issue!
Is the truck a manual? Could be the clutch interlock going bad. Also, look at the ignition switch on the steering column under the dash. -
-
K5 Tailgate Closing Assist
Hopefully your torsion rods aren't broken...- dvdswan
- Post #5
- Forum: Paint and Body
-
New member from SW TX
Welcome to the site. Love the barn doors.- dvdswan
- Post #18
- Forum: Introduction
-
New to Squarebodies
Welcome to the site. Nice find. Be careful driving it around the yard, it looks like the rear axle shifted.- dvdswan
- Post #7
- Forum: Introduction
-
How straight are our axles?
I'm not a lathe expert so it was just a guess. It seemed logical.- dvdswan
- Post #23
- Forum: Differential & Driveline
-
How straight are our axles?
So, do me a favor since you have a lathe. Attach one side of the axle to the lathe and leave the other unattached. See how much runout there is. I understand both sides are supported, one by the carrier and the other by the axle bearing. But a bent axle will eventually start wearing parts...- dvdswan
- Post #19
- Forum: Differential & Driveline
-
How straight are our axles?
No the bend is NOT there for a reason. The bend is there for who knows why, age, weight loaded, time, who knows. it should not be there.- dvdswan
- Post #8
- Forum: Differential & Driveline
-
How straight are our axles?
Think about this... the length of 30", with a tiny bend in the middle, as it spins the bend will want to force itself outward creating a vibration. A driveline is balanced just like a tire is balanced to 0 so there is not vibration. Same goes for axle shafts.- dvdswan
- Post #4
- Forum: Differential & Driveline
-
-
Can I Get a Quick Check Please?
cig ltr has its own fuse. accessory should only be hot with key in run or accessory. same with htr/ac.- dvdswan
- Post #3
- Forum: Tech Discussion
-
-
-
New from Missouri
Welcome to the site. Any pictures to share? We like pictures.- dvdswan
- Post #2
- Forum: Introduction
Latest posts
-
-
-
CUCV Brush Guard dimensions does anyone know them including the thickness of material?
- Latest: Trucktruxktrukk
