Search results
-
What have you done to your square lately??
I got one just like that. -
CAR ID Insane Shipping Costs.
I can get a $1.30 part from ALIBABA (China) for $1.30 shipped. NO SHIPPING CHARGE,- 73c20jim
- Post #3
- Forum: Tech Discussion
-
CAR ID Insane Shipping Costs.
Different Trend® - Lap Joint Clamp (2.25" ID, 2.25" OD, Length) Lap Joint Clamp (2.25" ID, 2.25" OD, Length) BCS-214 by Different Trend®. Material: Stainless. Inlet Diameter: 2.25". Outlet Diameter: 2.25". Different Trend provide variety of product selections, premium quality products, superior...- 73c20jim
- Thread
- Replies: 5
- Forum: Tech Discussion
-
What have you done to your square lately??
Thanks for advice. Going to use bypass for heatriser. Cannot purchase a exhaust pipe with proper flange anywhere - Autozone, NAPA, O'Reillys. Located a shop that can make a flange pipe. Closed till Monday. -
What new tools have you got lately?
I just found my 9/16 deep 3/8 drive socket. Errrrrrr! -
What have you done to your square lately??
Exhaust leak on passenger side. Three nuts for flange triangle surprisingly easy to remove. Flange on exhaust pipe is rotted off. Heat riser butterfly is gone. Autozone rents for free exhaust tools. I need a straight flange pipe about 8" long. Shouls be easy to replace. Should I replace heat... -
-
What new tools have you got lately?
9/16" 1/2" drive deep socket. No friggen idea where mine went. -
Taillights/Tag lights out
Rear lights have their own ground. Check that.- 73c20jim
- Post #11
- Forum: Electrical & Audio
-
What have you done to your square lately??
Thermostat reinstalled. Don't leak. Yeah me! -
-
New, help please!
Welcome. I have a center bearing with housing you can have for $10 plus shipping.- 73c20jim
- Post #3
- Forum: Introduction
-
steering column lower trim piece
You sent the wrong piece. It is not the piece pictures in my first post. Please advise. I can send it back to you. -
New guy eager to learn
Welcome from Tombstone, AZ.:banana-mario:- 73c20jim
- Post #23
- Forum: Introduction
-
What have you done to your square lately??
Nothing again yesterday. Well pump electronic box screwed up. Parts on order. So I guess I'll work on the truck today, once it gets over 50F. -
Please Welcome Classic Truck Consoles to GMSb!
Impeach them!- 73c20jim
- Post #12
- Forum: Classic Truck Consoles
-
What have you done to your square lately??
Nothing today. Had to fix the well pump. All good so far. -
Fuel gauge not accurate after filling up.
Extra octane that is NOT needed is not your friend.- 73c20jim
- Post #11
- Forum: Gauge, Speedo & Instrumentation
-
New impact: air vs battery powered?
Dewalt 20V battery. On sale Friday at LOWES. -
Source for speedometer cable adapter
It's an OEM part. Mine broke in half also. Luckily I have an aftermarket electronic speedometer that I adjusted to cover the discrepancy.- 73c20jim
- Post #2
- Forum: Transmission & Transfer Case
-
Fuel gauge not accurate after filling up.
Loose wire. Intermittent contact.- 73c20jim
- Post #6
- Forum: Gauge, Speedo & Instrumentation
-
Correct Choke Relay Location
It hooks up to an oil pressure switch so it only feeds power to the choke if there is oil pressure. The oil pressure switch is located just above the oil filter on the block. It is a SWITCH not a sender.- 73c20jim
- Post #3
- Forum: Engine & Performance
-
Timing a 350
What is your elevation. All readings are developed at sea level. Optimum vacuum is less as you go up. I have a post here about tuning and elevation. https://www.gmsquarebody.com/threads/high-elevation-tuning.27605/#post-527057- 73c20jim
- Post #14
- Forum: Engine & Performance
-
Fuel gauge not accurate after filling up.
Bad ground on sender???- 73c20jim
- Post #2
- Forum: Gauge, Speedo & Instrumentation
-
What have you done to your square lately??
Well, I'm going to get a new thermostat neck with the threaded hole on top. I'll put in it a twist drain thing. Did it on my racecar. It is good for bleeding air when filling, I believe. Other than that it will be a good conversation piece.
