projectmidnight74
Full Access Member
- Joined
- Jul 10, 2023
- Posts
- 115
- Reaction score
- 65
- Location
- Mississippi
- First Name
- Eddie
- Truck Year
- 1974
- Truck Model
- C10
- Engine Size
- V8
Got it. Feed me links to good bypasses for a carb system. Edelbrock based. Lol
Fuel return diy
- Thread starter projectmidnight74
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
projectmidnight74
Full Access Member
- Joined
- Jul 10, 2023
- Posts
- 115
- Reaction score
- 65
- Location
- Mississippi
- First Name
- Eddie
- Truck Year
- 1974
- Truck Model
- C10
- Engine Size
- V8
On second thought. I think I got it. Thanks for the advice and I will provide updates. Soon.
Ricko1966
Full Access Member
- Joined
- Apr 11, 2017
- Posts
- 5,452
- Reaction score
- 8,700
- Location
- kansas
- First Name
- Rick
- Truck Year
- 1975
- Truck Model
- c20
- Engine Size
- 350
See if you can exchange the 803 for an 803bp. If not I can explain a different method. I do not know if you will understand it or be able to accomplish it. Get another fitting like the one you have on the bottom of your regulator, solder the opening shut and drill a .060 orifice in it or see if you can tap it and put a carbureator jet with a .060 orifice in it. Now put that where your gauge ispresently,that will be your return. Move the gauge to the other side mounted on a tee. If you cant the whole mess a few degrees so the return port is the higher than the pressure port it will also bleed out vapor. Do not get me wrong. I still think a purpose built bypass regulator would be better. I am just using an approximate orifice the builders would know what actual diamension would work best.
Last edited:
Bextreme04
Full Access Member
- Joined
- May 13, 2019
- Posts
- 4,439
- Reaction score
- 5,581
- Location
- Oregon
- First Name
- Eric
- Truck Year
- 1980
- Truck Model
- K25
- Engine Size
- 350-4bbl
Why are you running an electric pump at all? Is this a high HP engine with no mechanical pump provisions or something?
AuroraGirl
Full Access Member
- Joined
- Sep 8, 2019
- Posts
- 9,693
- Reaction score
- 6,869
- Location
- Northern Wisconsin
- First Name
- Taylor
- Truck Year
- 1978, 1980
- Truck Model
- K10, K25
- Engine Size
- 400(?), 350
If OP is open to using a mechanical fuel pump, then edelbrock sells a mechanical pump that is internally regulated to the proper pressure for edelbrocks. Insulating the fuel lines near the engine/exhaust, and having a heat shield of some kind to deflect some road heat on the long sections will help with the fuel issue. The electric fuel pump can still be used, but it has to be one that the mechanical pump can "Suck through" , or else the pumps might fight eachother possibly.
projectmidnight74
Full Access Member
- Joined
- Jul 10, 2023
- Posts
- 115
- Reaction score
- 65
- Location
- Mississippi
- First Name
- Eddie
- Truck Year
- 1974
- Truck Model
- C10
- Engine Size
- V8
So, here is where we are. After buying the moroso fuel return line kit for $75 bucks, I attempted to install it and failed. 1 reason was because the adapter hoses were too thick to get on the filler neck and secure properly and 2 because the filler neck is the wrong size. I now have an in line fuel pressure gauge after removing the filter on the engine bay and have a full 3/8 return line running to the rear of the truck. The plan is now, with the correct filler hose, to use this 90 degree 3/8 barb and plumb it into the filler line and plug that return into that and it will dump directly into the tank. Wish me luck.
