fuel venting

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Ken B

Ken B

Full Access Member
Joined
Sep 18, 2019
Posts
1,191
Reaction score
1,455
Location
indiana
First Name
ken
Truck Year
81
Truck Model
c10
Engine Size
250
So the line with the white tape goes to the air cleaner, I understand and found where that connects. what I do not know is why is there a T in that line and were did or should it go? If not needed can I delete the T ?
You must be registered for see images attach
 
Ken B

Ken B

Full Access Member
Joined
Sep 18, 2019
Posts
1,191
Reaction score
1,455
Location
indiana
First Name
ken
Truck Year
81
Truck Model
c10
Engine Size
250
Question #2
The very small pvc line with green tape, hard to see, does that go to the port on the carb with the green tape? Lots of tubes with screws plugging them that I didnt do so I am just trying to confirm and re plumb these lines
You must be registered for see images attach
 
SquareRoot

SquareRoot

Full Access Member
Joined
Mar 18, 2017
Posts
4,192
Reaction score
8,030
Location
Arizona
First Name
Mike
Truck Year
85
Truck Model
K20
Engine Size
350
:mexsmoke::flamingdevil:
 

Attachments

  • Screenshot_20240828-154115.png
    Screenshot_20240828-154115.png
    268.8 KB · Views: 26
  • Charcoal.JPG
    Charcoal.JPG
    24.1 KB · Views: 26
Ken B

Ken B

Full Access Member
Joined
Sep 18, 2019
Posts
1,191
Reaction score
1,455
Location
indiana
First Name
ken
Truck Year
81
Truck Model
c10
Engine Size
250
Smart!
 
Ken B

Ken B

Full Access Member
Joined
Sep 18, 2019
Posts
1,191
Reaction score
1,455
Location
indiana
First Name
ken
Truck Year
81
Truck Model
c10
Engine Size
250
I think I have all of the lines for vapor capture done , except 1....the line with green tape at the canister and another green tape near the other end. where does this connect.
You must be registered for see images attach

You must be registered for see images attach

Didnt know if a carb pic would be helpful , there is a hose plugged with a screw that I need to figure out...unless that is where the last vapor line connects??
 
Oldbear42

Oldbear42

Supporting Member
Supporting Member
Joined
Feb 15, 2024
Posts
196
Reaction score
506
Location
Linden, Alberta, Canada
First Name
Shaine
Truck Year
1981
Truck Model
C20 LWB Scottsdale
Engine Size
350
TexasMan81 said:
In what form? Burnt wood or some other form of incinerated substance?
Click to expand...
I have used charcoal from fish tank filters before (new not used). It comes in a fabric bag and seemed to work to remove soldering fumes sucked through a small fan.
 
R

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,446
Reaction score
8,684
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
Ken B said:
I think I have all of the lines for vapor capture done , except 1....the line with green tape at the canister and another green tape near the other end. where does this connect.
You must be registered for see images attach

You must be registered for see images attach

Didnt know if a carb pic would be helpful , there is a hose plugged with a screw that I need to figure out...unless that is where the last vapor line connects??
Click to expand...
That plugged hose is not tothe cannister. I forget where it goes I'll look tomorrow. I think it's labeled port b check your emissions sticker. Pull back on your pic so I can see both ends of the mystery hose. I think it goes to a nipple on the air cleaner.
 
D

Daron58

Full Access Member
Joined
Jan 11, 2022
Posts
70
Reaction score
154
Location
Ponchatoula La.
First Name
Daron
Truck Year
75
Truck Model
C10
Engine Size
250 I6
Randy and Easton said:
Ken,

we had same issue. PO did the charcoal canister delete 2 port sending unit as well. Found that same steel line under radiator shroud and PO cut it drivers side bottom and that was it. We smelled gas all the time and could not find at the time a canister. I made a small charcoal filter out of a fuel filter and a fuel vent and mounted it on drivers side firewall. Fixed the gas smell and have never looked back.

Not sure if that is what your wanting but here are a few pics

Randy and E
Click to expand...
I understand the whole process but just wanted to ask if you just added the charcoal inside the glass filter housing around the center threaded with the filter screen inside or is there something I might be missing because the center that the filter ends screw onto doesn’t leave a lot of room for the charcoal and advise would be greatly appreciated Thanks
 
Randy and Easton

Randy and Easton

Full Access Member
Joined
Feb 6, 2021
Posts
900
Reaction score
1,303
Location
North Richland Hills, Texas
First Name
Randy
Truck Year
1976
Truck Model
C-10 LWB
Engine Size
350
Daron58 said:
I understand the whole process but just wanted to ask if you just added the charcoal inside the glass filter housing around the center threaded with the filter screen inside or is there something I might be missing because the center that the filter ends screw onto doesn’t leave a lot of room for the charcoal and advise would be greatly appreciated Thanks
Click to expand...
Yes, sorry. No filter just charcoal
 
You must log in or register to reply here.

Similar threads

D
Fuel crossover problem
Replies
1
Views
773
Dleslie212
D
KennedyHill
LS swap fuel system
Replies
11
Views
2K
TotalyHucked
TotalyHucked
projectmidnight74
Fuel return diy
2 3
Replies
36
Views
2K
Tonimus
Tonimus
G
Do I need a return fuel line with a calibrated 454?
Replies
3
Views
1K
Ricko1966
R
F
Fuel gauge
Replies
1
Views
549
Dmack
Dmack

Latest posts

Forum statistics

Threads
44,162
Posts
950,638
Members
36,273
Latest member
dannyphx
Top