What have you done to your square lately??

[KilgoreTrout]

I sprayed it on and used a putty knife.
Let it sit for an hour and trimmed it with a chef knife from the kitchen.
I'd use a super sharp knife.

You must be registered for see images

You must be registered for see images attach

 

[KilgoreTrout]

Then I hit it with a ******* DA sander and 80 grit. Haha...
I can't believe I'm doing this.

You must be registered for see images

 

[KilgoreTrout]

Trying to decide what to glaze it with. I don't have epoxy, but I'm a little hesitant on using bondo.
Would bondo glass work?
I don't have bedliner, either.
And I don't want black, I want stockish brown.
I have a can of white flex seal, but that's not brown, either. Hmm.....

 

[fmxr47]

Wrap it!


Sent from my iPhone using Tapatalk

 

[fmxr47]

Cut some plate for the bed today. Trying to figure out a light layout, license plate will be centered.

You must be registered for see images

You must be registered for see images

You must be registered for see images

The middle or bottom lights will be the white reverse lights


Sent from my iPhone using Tapatalk

 

[KilgoreTrout]

Wrap it!


Sent from my iPhone using Tapatalk

Hmm......I could do that.
Like just with vinyl and glue?
I saw someone do that on a square, though, and it looked like total ****.
It has to be doable, though.

 

[Dmack]

Worked on my door panels. Not great, but better than faded tan and dirty fabric.

You must be registered for see images attach

 

[bucket]

Trying to decide what to glaze it with. I don't have epoxy, but I'm a little hesitant on using bondo.
Would bondo glass work?
I don't have bedliner, either.
And I don't want black, I want stockish brown.
I have a can of white flex seal, but that's not brown, either. Hmm.....

I've used 3m Polyester Glaze, it worked well.

 

[73c20jim]

Gauges are driving me nuts. Ordered some clips and will be running my own grounds to the circuit board.

Trying to figure out door locks. Had them in before, but now have to redo them. That stupid clip that holds on the L thing is a bitch. Service manual is no help.

Cleaned out all blower ducts. Ready to go in.

Sorted out thru my parts. Can't find one or two or more that I need.

Tried to clean off **** from new (to me) steering wheel. This is larger diameter that the one on the truck. Hope WD40 to the rescue.

Looks like I need a part for each job I'm trying to do. Two orders placed to LMC.

Feel like getting nowhere fast.

And by 1100 each day it's over 93F. Short window to work each day.

 

[82sbshortbed]

Cleaned out all the leaves under the windshield wipers and painted the plastic thingy black.

You must be registered for see images attach

 

[78C10BigTen]

What have i done you ask....? I drove it to work and back just as i do everyday lol

 

[Old77]

To make @Big Chip happy I been working on my headliner a little bit at a time over this last week. Headliner board repaired and we’re close to gluing down the headliner material. Might have it back in the truck this weekend

You must be registered for see images attach

Getting her tinted this weekend, too

 

[Old77]

How did the headliner project go @Old77?

See my last post. Making progress on it this week. Should be back in soon

 

[82Diesel]

Ordered this Big ass Drivers Floor Made in the USA (Motorcity actually - Detroit, MI) 24 Gauge Steel.
None of that Taiwan BS... The biggest one on the market 24" x 33" Order it here. https://www.ebay.com/itm/1973-1987-Chevy-Truck-GMC-Jimmy-Suburban-Blazer-Left-Extended-Front-Floor-Pan/142123453539?ssPageName=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649

Getting ready to Buy Footwell Patch Panels & Some Really Mint Clean Electric Doors & Fenders

You must be registered for see images attach

 

[Blue Ox]

I hate to break this to you, but those aren't OEM.