To remove or not to paint frame?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Toad455

Full Access Member
Joined
Aug 3, 2023
Posts
103
Reaction score
72
Location
North Texas
First Name
Kevin
Truck Year
1978
Truck Model
C10
Engine Size
6.0
Hello, I'm not sure if I should have posted this in the paint and body section but since it's suspension I figured I'd start here. I'm fixing to sand blast and paint my frame for my 78 2wd. My question is I'm not sure if I should remove the lower front frame cross piece that's under the engine, that the lower control arm u bolts attach to. I believe it will clean up and paint easier if apart, there's only three bolts on each side that hold it in, BUT it also seems like it may be a pain and maybe I should just leave it alone since it's in the correct position. Would any of you remove it just to paint? Thanks.
 

TotalyHucked

Full Access Member
Joined
Feb 24, 2020
Posts
3,545
Reaction score
11,411
Location
Auburn, Georgia
First Name
Zach
Truck Year
1985
Truck Model
Sierra 1500
Engine Size
5.3
They're not bolts, they're rivets and they're a PITA to remove. Depends on how far you're going with the build. Cool little cruiser/driver or super nice show truck?
 

Fri00

Junior Member
Joined
Apr 1, 2024
Posts
6
Reaction score
2
Location
PA
First Name
Shaun
Truck Year
1982
Truck Model
C10
Engine Size
N/A
are you referring to the entire k member? If so that’s a pretty straightforward unbolt. Anything riveted I would say it’s not worth it unless they’re damaged or there’s rot.
 

legopnuematic

Licensed Junk Dealer
Supporting Member
Joined
Oct 27, 2016
Posts
2,416
Reaction score
6,094
Location
MO
First Name
Spencer
Truck Year
1971, 1̶9̶7̶4, 1976, 1979,1̶9̶8̶5, 2002
Truck Model
Dart Swinger, Sierra 10, C10 Cheyenne, C10 Big Ten, Silverado 10, Ram 2500
Engine Size
225/6, 350 c.i., 350 c.i., 5.9l Cummins
On my 79, I had the frame blasted as a unit, as having it be a roller was important at the time, then I disassembled it, cleaned the remaining areas with a purple 3m wheel, then painted and reassembled.

If you look at my 79 thread in my signature, starting at post 495 shows that process.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach
 

Toad455

Full Access Member
Joined
Aug 3, 2023
Posts
103
Reaction score
72
Location
North Texas
First Name
Kevin
Truck Year
1978
Truck Model
C10
Engine Size
6.0
They're not bolts, they're rivets and they're a PITA to remove. Depends on how far you're going with the build. Cool little cruiser/driver or super nice show truck?
This one has three bolts on each side. The support underneath the engine. I'm building it as show and light driving but no mirrors on the floor or anything like that. Just local shows.
 

Toad455

Full Access Member
Joined
Aug 3, 2023
Posts
103
Reaction score
72
Location
North Texas
First Name
Kevin
Truck Year
1978
Truck Model
C10
Engine Size
6.0
are you referring to the entire k member? If so that’s a pretty straightforward unbolt. Anything riveted I would say it’s not worth it unless they’re damaged or there’s rot.
Yes, I believe it's the k member, no rivets that I can see.
 

Toad455

Full Access Member
Joined
Aug 3, 2023
Posts
103
Reaction score
72
Location
North Texas
First Name
Kevin
Truck Year
1978
Truck Model
C10
Engine Size
6.0
On my 79, I had the frame blasted as a unit, as having it be a roller was important at the time, then I disassembled it, cleaned the remaining areas with a purple 3m wheel, then painted and reassembled.

If you look at my 79 thread in my signature, starting at post 495 shows that process.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach
Nice, thank you. I'll check out your thread. That cross member looks heavy.
 

legopnuematic

Licensed Junk Dealer
Supporting Member
Joined
Oct 27, 2016
Posts
2,416
Reaction score
6,094
Location
MO
First Name
Spencer
Truck Year
1971, 1̶9̶7̶4, 1976, 1979,1̶9̶8̶5, 2002
Truck Model
Dart Swinger, Sierra 10, C10 Cheyenne, C10 Big Ten, Silverado 10, Ram 2500
Engine Size
225/6, 350 c.i., 350 c.i., 5.9l Cummins
Nice, thank you. I'll check out your thread. That cross member looks heavy.
It’s not too bad, maybe 50lbs give or take?
 

Toad455

Full Access Member
Joined
Aug 3, 2023
Posts
103
Reaction score
72
Location
North Texas
First Name
Kevin
Truck Year
1978
Truck Model
C10
Engine Size
6.0
It’s not too bad, maybe 50lbs give or take?
After seeing your pics it's coming out today,ha. May as well since I can blast it at home like I did the cab and all the other parts. If I don't do it I'll regret it later even if you can't tell whether or not it's been out, but I'll know.
 

Toad455

Full Access Member
Joined
Aug 3, 2023
Posts
103
Reaction score
72
Location
North Texas
First Name
Kevin
Truck Year
1978
Truck Model
C10
Engine Size
6.0
On my 79, I had the frame blasted as a unit, as having it be a roller was important at the time, then I disassembled it, cleaned the remaining areas with a purple 3m wheel, then painted and reassembled.

If you look at my 79 thread in my signature, starting at post 495 shows that process.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach
Lego, on your second pic from the top, what are those two plates on the floor? I see them bolted on in your top pic. Are those just for lifting? Thanks.
 

legopnuematic

Licensed Junk Dealer
Supporting Member
Joined
Oct 27, 2016
Posts
2,416
Reaction score
6,094
Location
MO
First Name
Spencer
Truck Year
1971, 1̶9̶7̶4, 1976, 1979,1̶9̶8̶5, 2002
Truck Model
Dart Swinger, Sierra 10, C10 Cheyenne, C10 Big Ten, Silverado 10, Ram 2500
Engine Size
225/6, 350 c.i., 350 c.i., 5.9l Cummins
Lego, on your second pic from the top, what are those two plates on the floor? I see them bolted on in your top pic. Are those just for lifting? Thanks.
Brackets for a tow bar I made when I flat towed the truck once.

You must be registered for see images attach

You must be registered for see images attach
 

Forum statistics

Threads
43,942
Posts
946,222
Members
35,987
Latest member
finley446
Top