Help I found this in my oil pan, any idea what its from?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Mike Curtis

Junior Member
Joined
Mar 24, 2019
Posts
21
Reaction score
6
Location
Charlotte North Carolina
First Name
Mike
Truck Year
1979
Truck Model
4wd LWB Silverado k10
Engine Size
350
Bought a used gm crate motor to swap into my vehicle, its a 1990 block, stamped built in Mexico, the typical off the shelf gm goodwrench low compression motor. I heard it run before it was pulled and now I've got it home and decided to inspect under the valve covers and the oil pan. The valve covers were dirty, with a bit of sludge, so I scraped it a bit and took a shop vac to clean it out. then I turned while it was on the stand, I removed the oil pan before turning it upside down. The oil pan had a film of sludge about 1/16" thick in the bottom, I've seen worse, but when I cleaned it out, I found this. A rivot and looks to be a keeper? Any ideas what this is from? Any help is appreciated. It is steel and the quarter is for visual reference, lol, it wasn't in the oil pan. thanks
You must be registered for see images attach
 

Bextreme04

Full Access Member
Joined
May 13, 2019
Posts
4,439
Reaction score
5,581
Location
Oregon
First Name
Eric
Truck Year
1980
Truck Model
K25
Engine Size
350-4bbl
That was my thought too, looks like a link from a timing chain. If you have it on a stand i'd pull the timing cover and take a good close look at that chain. Worst case it is busted or worn and you can swap it out for a good new one for pretty cheap before you drop the motor in.
 

Mike Curtis

Junior Member
Joined
Mar 24, 2019
Posts
21
Reaction score
6
Location
Charlotte North Carolina
First Name
Mike
Truck Year
1979
Truck Model
4wd LWB Silverado k10
Engine Size
350
Also, I've gotten feedback the rivot it probably from a shield under the intake. Is it worth taking the intake off to see if 1) there are more there, 2) put that one back in?

or, should I just assume one came out during assembly back in 1990 and has been laying in the bottom of the oil pan for 30 years?
 

Turbo4whl

Supporting Member
Supporting Member
Joined
Oct 30, 2019
Posts
3,126
Reaction score
7,257
Location
Downingtown, PA
First Name
Wayne
Truck Year
1974
Truck Model
Jimmy
Engine Size
350
So how would I tell, just look to see if it's all there? Or is there something else I should look for?

Yes. Look for any missing links. Most likely the chain and gears have already been replaced and that is just a left over piece that did not get cleaned out.
 

Mike Curtis

Junior Member
Joined
Mar 24, 2019
Posts
21
Reaction score
6
Location
Charlotte North Carolina
First Name
Mike
Truck Year
1979
Truck Model
4wd LWB Silverado k10
Engine Size
350
thank guys, so heres where I am so far.
I pulled the timing cover and found 1 more rivet in the cover, and 1 lodged in the timing chain. No missing links, but 1 broken. I put on a new chain. Here's the pics of what I found. As much as I don't want to, (mostly because I haven't done one before, I will pull the intake next to see if any more loose rivets are floating around in there) I read there are 4 holding the shield on, I will feel a little better if I find 3 holes and 1 rivet remaining. If I can't find the last one, maybe it got flushed through an oil change? Time will tell.
Btw, no surprise the old chain was really loose.
You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach
 

Turbo4whl

Supporting Member
Supporting Member
Joined
Oct 30, 2019
Posts
3,126
Reaction score
7,257
Location
Downingtown, PA
First Name
Wayne
Truck Year
1974
Truck Model
Jimmy
Engine Size
350
That is a shame the rivets found their way to the timing chain. Looks like where the one rivet is stuck in the chain, that center link is missing.

You will be fine pulling the intake. Follow the torque specs and sequence when installing. I like Fel-Pro, perm-a-torque gaskets. Put a little silicone sealer at the four corners where the block top edge gaskets meet the gaskets on the heads.
 

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,693
Reaction score
6,869
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
I have an old timing chain laying on the floor collecting rust and dust, want it? I just can't remember if I threw it outside or in a scrap barrel
 

DoubleDingo

Full Access Member
Joined
Jul 3, 2012
Posts
11,251
Reaction score
17,177
Location
Right where I am
First Name
Bagoomba
Truck Year
1981
Truck Model
81-C20 Silverado Camper Special-TH400-4.10s
Engine Size
Carb'ed Vortec 350
I have an old timing chain laying on the floor collecting rust and dust, want it? I just can't remember if I threw it outside or in a scrap barrel

He installed a new chain
 

Latest posts

Forum statistics

Threads
44,168
Posts
950,776
Members
36,283
Latest member
Cantrell299
Top