Haynes manual suggest silicone dielectric grease for ignition module?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

scrap--metal

Full Access Member
Joined
Sep 15, 2021
Posts
691
Reaction score
1,314
Location
MN
First Name
Calvin
Truck Year
'85, '81
Truck Model
K10, K20
Engine Size
305, 350
You can have a Thermal paste that is also dielectric(most are, but NOT all).

You can also have a dielectric grease that is not thermally conductive.

The DC-4 is not a good thermal conductor and is a silicone dielectric grease.
The Super Lube Heat Sink compound I linked above is a Silicone dielectric grease that has metal particles blended in to make it a good thermal conductor.
^ I'm in this camp. As long as it's thermally conductive enough, it should work.

That makes me wonder what the thermal conductivity of the paste they used in the factory was? If the new stuff (thermal paste, dielectric grease, etc.) has the same thermal conductivity value (K measured in W/[m*K]) as it the factory thermal paste, then it shouldn't matter what the name on the tube, bottle, syringe says.
 

Originalthor

Full Access Member
Joined
Aug 22, 2021
Posts
1,085
Reaction score
3,662
Location
Saskatoon Saskatchewan
First Name
Scott
Truck Year
1989
Truck Model
Suburban
Engine Size
5.7
You guys know that thermal paste was not invented till the 2000s and computers got super fancy. Sure there was some other products out back then in the 90s but you had to have some big bucks to spend on a computer So technically speaking the manual is correct for the era of vehicle it was made for.

Dielectric grease was used or any grease really. Now recommended is thermal paste. I've used both. Don't matter usually the part is a POS and fails anyways.
 

Doppleganger

Full Access Member
Joined
May 24, 2019
Posts
12,684
Reaction score
58,828
Location
OH-MI: Just like it sounds
First Name
Chris
Truck Year
1985
Truck Model
K20
Engine Size
5.7
Friend of mine's dad wires aircraft at the local airport with new electronics upgrades. I asked him about the DC-4 and he said they buy it by the case there. Sound like what I'll use to rewire my square.
 

Camar068

Supporting Member
Supporting Member
Joined
Feb 5, 2014
Posts
4,293
Reaction score
3,339
Location
Kentucky
First Name
David
Truck Year
1986
Truck Model
K10/LM7 5.3/4L60e/np208/3.73/32"
Engine Size
10 yrs Air Force
Not necessarily. As I said before, they are simply characteristics. They are not mutually exclusive.

You can have a Thermal paste that is also dielectric(most are, but NOT all).

You can also have a dielectric grease that is not thermally conductive.

The DC-4 is not a good thermal conductor and is a silicone dielectric grease.
The Super Lube Heat Sink compound I linked above is a Silicone dielectric grease that has metal particles blended in to make it a good thermal conductor.

They are both silicone based dielectric greases, but only one of them is also a thermal paste.
sorry about that, I took work experience at work to heart a bit. I'll make sure we don't have any DC-4 if it's got metal in it lol. Don't need someone grabbing the wrong tube by accident.

Working on medical equipment, more specifically, x-ray equipment we are very particular. The heavy duty cables that plug into the x-ray tube require dielectric grease....and there's 3 pins on each connector about 8mm apart. We're talking 60KV on each cable....so we don't like arcing at all lol. Price varies from $4,500 - $140,000 to replace an x-ray tube for a simple error in using the wrong product.
 

SirRobyn0

Full Access Member
Joined
Dec 6, 2019
Posts
6,755
Reaction score
11,402
Location
In the woods in Western Washington
First Name
Rob
Truck Year
1984
Truck Model
C20
Engine Size
305
^ I'm in this camp. As long as it's thermally conductive enough, it should work.

That makes me wonder what the thermal conductivity of the paste they used in the factory was? If the new stuff (thermal paste, dielectric grease, etc.) has the same thermal conductivity value (K measured in W/[m*K]) as it the factory thermal paste, then it shouldn't matter what the name on the tube, bottle, syringe says.
This is a very good point.

You guys know that thermal paste was not invented till the 2000s and computers got super fancy. Sure there was some other products out back then in the 90s but you had to have some big bucks to spend on a computer So technically speaking the manual is correct for the era of vehicle it was made for.

Dielectric grease was used or any grease really. Now recommended is thermal paste. I've used both. Don't matter usually the part is a POS and fails anyways.
I wondered about that, as I had no idea, I just new that pretty much the only place you could get it at was computer / electronics stores.

I think we have our answer right there.
 

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
30,438
Reaction score
28,337
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
The '78-'83 GM wiper delay modules I've taken apart have had white thermal paste in them, so it must have been around before the 00's.

I've always used dielectric grease and it's never let me down. A lot of modules even come with a little squeeze tube of it. Now with that said, I do agree that a thermal paste would be the proper material to use.
 

1lejohn

Full Access Member
Joined
May 14, 2012
Posts
325
Reaction score
749
Location
texas
First Name
john
Truck Year
1985 , 2004
Truck Model
k-1500, 2500 HD
Engine Size
350, 6.7
As a side note I always put a dab of the silicon grease on my spark plug wires. It keeps them from sticking to the plugs and or cap terminals.
 

Matt69olds

Full Access Member
Joined
Jan 8, 2018
Posts
2,451
Reaction score
3,819
Location
Central Indiana
First Name
Matt
Truck Year
81
Truck Model
GMC 1/2 ton
Engine Size
455 Olds
You guys know that thermal paste was not invented till the 2000s and computers got super fancy. Sure there was some other products out back then in the 90s but you had to have some big bucks to spend on a computer So technically speaking the manual is correct for the era of vehicle it was made for.

Dielectric grease was used or any grease really. Now recommended is thermal paste. I've used both. Don't matter usually the part is a POS and fails anyways.


I’m pretty sure it’s mentioned in the factory manual to use thermal paste. I’m sure the book says to use GM part number whatever, but whatever it’s called it’s a heat transfer paste.
 

Doppleganger

Full Access Member
Joined
May 24, 2019
Posts
12,684
Reaction score
58,828
Location
OH-MI: Just like it sounds
First Name
Chris
Truck Year
1985
Truck Model
K20
Engine Size
5.7
Bosch LH2.4 fuel injection was used on dozens of European cars. One of the major components was a power stage that was bolted to an aluminum base on the inside of the fender with a nice layer of white thermal paste between them. It debuted in 1989.
 

Originalthor

Full Access Member
Joined
Aug 22, 2021
Posts
1,085
Reaction score
3,662
Location
Saskatoon Saskatchewan
First Name
Scott
Truck Year
1989
Truck Model
Suburban
Engine Size
5.7
True on the white paste but it was not technically thermal paste. Its just a thick silicone/grease white paste that has a higher melting point. And it worked. They needed to put it on the pmd's on the 6.5 turbo diesels lol.


Thermal paste some are still silicone/grease based but has metal oxides in it. The more expensive have fancy better oils, silvers, and what other crap they put in it to make it.

I use artic silver 3 i think it is on my computer projects. For fun I had a old computer and we tried tooth paste even. It worked. To a degree lol.
 

Hugomartin

Banned
Joined
Jul 23, 2021
Posts
256
Reaction score
71
Location
Nc
First Name
Hugo
Truck Year
1987
Truck Model
V20 3/4 ton 5.7 350 suburban
Engine Size
350
Truck defnitly seems to run better no stalling at stop lights and downhill . Very tight spot on the truck for that dern inition module. I appreciate the help.
 

legend57

Supporting Member
Supporting Member
Joined
Jan 11, 2022
Posts
59
Reaction score
109
Location
San Jose, CA
First Name
Rob
Truck Year
1976
Truck Model
K20
Engine Size
400
I've experienced the same failures in the past. Always used the thermal paste, but still had failures with store brand modules. I stick with AC Delco because they tend to last longer. I still keep a spare in the glove box.
I found this interesting article:

It is true the conductive grease has a higher thermal conductivity coefficient than dielectric grease, but because the intended gap is so thin (microns), you can almost put anything in there and it will be much better than metal on metal. The best part of the thermal paste and even dielectric grease is they won't flow when hot and wash out. Little microscopic air pockets are the killer in electrical connections like this.

Whichever you use, dielectric grease or thermal paste, the key is to make it ultra thin. A thick layer of goo between the metal surfaces will create a high thermal resistance barrier and you'll cook the module, regardless of which one you use. Also, make sure mounting screws are tight, and definitely not stripped. Clamping pressure is needed to maintain the micro-gap. Just having the surfaces close together is not enough. High contact pressure needs to be maintained.
 

MikeB

Full Access Member
Joined
Apr 4, 2014
Posts
1,775
Reaction score
1,004
Location
North Texas
First Name
Mike
Truck Year
1969
Truck Model
C10
Engine Size
355
So the Haynes is wrong?

Absolutely!

On another note, GM modules were very reliable, but the same is (was?) true for MSD and even Accel. My truck's MSD module was installed sometime around Y2K. But today, who knows where any of them are manufactured, and to what standards? My experience with AC Delco electric/electronic parts has been good, even if most of them are made in Mexican plants. I suspect the AC Delco folks have higher quality standards than modules sold on eBay.
 
Last edited:

MikeB

Full Access Member
Joined
Apr 4, 2014
Posts
1,775
Reaction score
1,004
Location
North Texas
First Name
Mike
Truck Year
1969
Truck Model
C10
Engine Size
355
You guys know that thermal paste was not invented till the 2000s and computers got super fancy. Sure there was some other products out back then in the 90s but you had to have some big bucks to spend on a computer So technically speaking the manual is correct for the era of vehicle it was made for.

Dielectric grease was used or any grease really. Now recommended is thermal paste. I've used both. Don't matter usually the part is a POS and fails anyways.
I used thermal thermal paste when I worked as an electronic technician in the 1970s. A common use on a variety of electronic equipment was for mounting a power transistor to a heat sink.

Something like this:
 

Attachments

  • heat sink.jpg
    heat sink.jpg
    7.9 KB · Views: 41

Forum statistics

Threads
44,152
Posts
950,452
Members
36,268
Latest member
JUKA
Top