AFR gauge installation
- Thread starter leejewell
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
nvrenuf
Full Access Member
- Joined
- Jul 30, 2010
- Posts
- 2,070
- Reaction score
- 2,745
- Location
- Mobile, Al.
- First Name
- John
- Truck Year
- 1991
- Truck Model
- K5
- Engine Size
- 454
Does your a/c work? If not, are you going to fix it?
75gmck25
Full Access Member
- Joined
- Oct 13, 2016
- Posts
- 2,400
- Reaction score
- 2,431
- Location
- Northern Virginia
- First Name
- Bruce
- Truck Year
- 1975
- Truck Model
- K25 Camper Special TH350 NP203
- Engine Size
- 5.7
Is it a wideband gauge, and does it have a heated sensor?
No heated sensor - usually needs to be within a few inches of the collector, or in the collector fitting. This because it needs the exhaust heat to read properly.
Heated sensor - anywhere between the collector and the muffler or crossover. Exact location is more flexible, but you don’t want leaks in the pipes in front of it to screw up the reading.
All O2 sensors - bung should be pointed straight up or within about 30-45 degrees of straight up. This ensures residual moisture from the cooling exhaust pipe does not collect on and contaminate the sensor.
Make sure everything in the wideband gauge wiring is grounded to a single point, which is then grounded to the engine and body. The gauge works by reading very small voltage variations at the sensor, so you do not want any difference in ground potential to throw it off.
No heated sensor - usually needs to be within a few inches of the collector, or in the collector fitting. This because it needs the exhaust heat to read properly.
Heated sensor - anywhere between the collector and the muffler or crossover. Exact location is more flexible, but you don’t want leaks in the pipes in front of it to screw up the reading.
All O2 sensors - bung should be pointed straight up or within about 30-45 degrees of straight up. This ensures residual moisture from the cooling exhaust pipe does not collect on and contaminate the sensor.
Make sure everything in the wideband gauge wiring is grounded to a single point, which is then grounded to the engine and body. The gauge works by reading very small voltage variations at the sensor, so you do not want any difference in ground potential to throw it off.
nvrenuf
Full Access Member
- Joined
- Jul 30, 2010
- Posts
- 2,070
- Reaction score
- 2,745
- Location
- Mobile, Al.
- First Name
- John
- Truck Year
- 1991
- Truck Model
- K5
- Engine Size
- 454
Ok. If you weren’t using the a/c vent I’d say install the gauge in that hole using some rough textured plastic (Lowe’s and HD carry it).
You could do the same with the radio hole.
The only other alternative is to put it on the column or hanging along the bottom of the dash.
nvrenuf
Full Access Member
- Joined
- Jul 30, 2010
- Posts
- 2,070
- Reaction score
- 2,745
- Location
- Mobile, Al.
- First Name
- John
- Truck Year
- 1991
- Truck Model
- K5
- Engine Size
- 454
CoggedBelt75
Full Access Member
- Joined
- Jul 31, 2010
- Posts
- 43,796
- Reaction score
- 179,943
- Location
- Oklahoma
- First Name
- Joe
- Truck Year
- 1975
- Truck Model
- C10
- Engine Size
- 383
Here's where I have my Innovate A/F gauge
You must be registered for see images attach
- Joined
- Oct 27, 2016
- Posts
- 3,045
- Reaction score
- 8,346
- Location
- MO
- First Name
- Spencer
- Truck Year
- 1971, 1̶9̶7̶4, 1976, 1979,1̶9̶8̶5, 2002
- Truck Model
- Dart Swinger, Sierra 10, C10 Cheyenne, C10 Big Ten, Silverado 10, Ram 2500
- Engine Size
- 225/6, 350 c.i., 350 c.i., 5.9l Cummins
Old picture but this is where I mounted the gauge in my 76.
You must be registered for see images attach
- Joined
- Oct 30, 2019
- Posts
- 3,230
- Reaction score
- 7,590
- Location
- Downingtown, PA
- First Name
- Wayne
- Truck Year
- 1974
- Truck Model
- Jimmy
- Engine Size
- 350
Race truck? I see a roll bar...
nvrenuf
Full Access Member
- Joined
- Jul 30, 2010
- Posts
- 2,070
- Reaction score
- 2,745
- Location
- Mobile, Al.
- First Name
- John
- Truck Year
- 1991
- Truck Model
- K5
- Engine Size
- 454
No, this one is just a wheeler. The cage is because it’s a full top but some of its parts are from my last truck that was a wheeler + deep pit racer.
SquareRoot
Full Access Member
- Joined
- Mar 18, 2017
- Posts
- 4,291
- Reaction score
- 8,351
- Location
- Arizona
- First Name
- Mike
- Truck Year
- 85
- Truck Model
- K20
- Engine Size
- 350
Buy EFI and/or Dakota Digital. Then you can see it on your gauge panel or phone.
Similar threads
