Search results

  1. G

    Irregular valve tip wear pattern

    I agree with MikeB. The guide plates are not aligned and causing the rockers to not contact the stems properly. The solution is either correct the geometry with these heads or replace them. You might be able to utilize offset rockers but that isn't common.
  2. G

    Irregular valve tip wear pattern

    What type of rockers did you have on these?
  3. G

    383 guys: stock oil pan interference issues?

    The pan should not be an issue unless it is bent. The depth of the pan is determined by the clearance issue of the vehicle. The block should be milled for clearance of the rods and that is a known issue with the build you are doing.
  4. G

    crew cab carpet?

    Yes. I did a scuff sanding and adhesive but I used a trim place from the back of the headliner to secure the end near the back glass.
  5. G

    1978 Jimmy wiper switch

    I used the factory harness from the wiper switch to the pulse module and the painless harness from the module to the wiper motor. The connections on the module for the painless wires I used are B-pink 963 C-purple 964 D-ground...
  6. G

    easiest way to install aftermarket gauges?

    There is not a plug on the market to plug up to the harness. You can purcahse plg bodies and build your own, which I would recommend. The idea of unplugging all those wires one at a time is enough to make you want to drive a Ford.
  7. G

    Fuel gauge not working ? New sending units

    purple wire shopuld be grounded to the frame and the pink wire should be attached to the sending unit.
  8. G

    crew cab carpet?

    I bought mine from LMC and it fit great. I did buy the crew cab carpet but my truck isn't a crew cab; I used the extra carpet to cover the back of the cab since I have buckect seats in it.
  9. G

    1978 Jimmy wiper switch

    Which Painless harness do you have? Is it the universal or the truck specific? I just finished installing one on my truck that was specific and can give you the wire numbers if you have the same one.
  10. G

    Carb swap question

    I have the Edelbrock brackets on mine. They installed easily and they tranny side has to be adjusted for the vehicle.
  11. G

    Cam choice

    Cam selection depends somewhat on several things. What are you doing to the engine? What rpm range is it going to work in? What is the axle ratio?
  12. G

    Dual Exhaust system

    89Suburban they make cats for headers that will pass in most states. Guess I am the odd ball on this subject, but I prefer the Pypes Street Pro mufflers.
  13. G

    New to site from north texas

    Welcome to the site. Nice looking truck!
  14. G

    wiring problems

    You either have a bad ground or bad motors.
  15. G

    Rubber flooring advice

    Yes it is a little less than 1/8" thick. Must people never notice it.
  16. G

    Electrical Schematics

    Glad to help.
  17. G

    wiring problems

    If a test light indicates power then you must have a ground problem. Wait, did you have the switch on when you tested it?
  18. G

    Transfer case issues

    Sounds like an internal issue with the gears or chain. I am not familar enough but one the the 4 wheeling guys will help you out, hang loose for a bit.
  19. G

    What have you done to your square lately??

    I have not done much to mine but I have been heping out on 3-4 others.
  20. G

    fuel pump

    That should be enough to pick up.
  21. G

    asstance with finding wheel spacers for 77 C10

    It is not wasting your breath to speak up. We have a fair exchange of inforamtion here and if something I said is inaccurate then it needs to be corrected.
  22. G

    Rubber flooring advice

    Yes, the Dynamat adheres to the floor very tightly.
  23. G

    New Guy From GA

    Nice looking avatar.
  24. G

    Turbo 350C to 4L60E

    I have a noticable difference.
  25. G

    electric window motor

    Close Bucket. If your truck has the lower cover on the door you can drill the door skin, drill out the rivets and remove the motor and not have to remove the regulator at all. Oops, almost forgot you still need to secure the glass before removing the motor.

Latest posts

Forum statistics

Threads
44,613
Posts
962,537
Members
37,154
Latest member
BrianBaca
Top