Search results

  1. Craig Nedrow

    1964 Chevy ll ls1/t56 swap

    Called Church Brothers Racing, I like there rear tir 4 link, The pic shows a Ford 9", and I have two, and will narrow them in house. According to them, the rearend is narrowed about 2" a side, from stock.
  2. Craig Nedrow

    1964 Chevy ll ls1/t56 swap

    called Clay Mullis @ Full Tilt street rods, here is the kit: This will have GM 11" Metric brakes, Viking double adj coil overs, power rack and pinion. This will be fast and easy to install, and comes with LS motor mounts, and a universal trans mount for the T56.
  3. Craig Nedrow

    1964 Chevy ll ls1/t56 swap

    Yep, spent quite a bit of time there. I think the Fab Quest inserts will do good. Got a pic of you car rear setup?
  4. Craig Nedrow

    1964 Chevy ll ls1/t56 swap

    will mini tub as I love the wide back tires: This in my opinion is the cheap, fast, and easy way to tub a Chevy ll. Saw Chip Foose do it on youtube.
  5. Craig Nedrow

    1964 Chevy ll ls1/t56 swap

    I also plan on using double adjustable Shocks, like these:
  6. Craig Nedrow

    1964 Chevy ll ls1/t56 swap

    I think the fastest and easiest front suspension could be the CPP, like this
  7. Craig Nedrow

    1964 Chevy ll ls1/t56 swap

    So as I get closer to working on the nova, I wanted feedback from any of you nova guys. I have scrounged two mustang ford 9" rears, though I know they will have to be shortened. Plan on using Church Boys tri bar four length. I also can get an 8.8 Explorder rearend, they are great, easy to...
  8. Craig Nedrow

    Garage upgrade

    Dang it Paul....I was just thinking I needed to get a opener for the shop door, it is heavy. I know that you can adjust the springs, and in the past I have, but it was a little scary. No way I am doing that now. Dang, gotta get one..
  9. Craig Nedrow

    Spray booth??

    Check into renting a booth, may be cheaper then you think.
  10. Craig Nedrow

    AN fittings need to be drilled?

    all the jets in your carb will not flow near that volume.
  11. Craig Nedrow

    3 minute battery life…?

    To perform a voltage drop test on the battery cable, you should connect one of the voltmeter’s leads to the starter motor battery terminal, while the other end is connected to the positive battery terminal. The engine, battery, cables, and connections must be in good working order for an...
  12. Craig Nedrow

    Questions about... My rear end?

    There is also the Yukon lunchbox locker, I love mine, 14 FF.
  13. Craig Nedrow

    Differential swap / going to look at a rear end

    my 86 is 4:10
  14. Craig Nedrow

    Dingleball Hones

    I don't really like them, but as a former engine builder, go with the 400. It would be much better to take to a machine shop.....just saying. Yes it will cost more. I do have one in my tool box though, never used.
  15. Craig Nedrow

    Hello, my name is Derek, and I have Just joined this page, trying to find some good information on working on my new 1978 k30

    That was like "cool man," back in the day. I had one in the 67 Charger, yeah it sounded cool.
  16. Craig Nedrow

    High oil pressure after replacing pump

    In theory, (I love to live there,) you need 10 lbs pressure for each 1000 rpm. My Moroso pump comes with three springs, I have the 70 psi spring as I plan on wickin up the 489 hopefully to 7000 rpm, but it might only make it 6500, as the AFR heads are the 265's, but now fully ported. I'de be...
  17. Craig Nedrow

    Eaton MLocker

    I have a yukon lunchbox locker in the 14ff, and a Spicer lunchbox locker in the D44 front, like em.
  18. Craig Nedrow

    New from northern Maine

    There was a little pub up the hill, so I asked a number of folks where to get a good traditional lobster, that place was the consensus. Been riding three weeks by then, and was a little lean and unkept, but the swank dressers were really nice, it was just the coolest.
  19. Craig Nedrow

    Granger Smith aka Earl Dibbles Jr. father's 74 GMC full restoration videos.

    I did not know that, probably because I am never up that late. He seem like a real good guy.
  20. Craig Nedrow

    BBC 489 build

    This truck also has the big brakes as it was a camper special 8200 GVW rating, so will clean, paint, turn and all new brake parts. Really glad to have these big brakes. It sure is nice to have a doner vehicle. Speaking of doner, I am getting one complete ford 9" 59.5 inches wide, complete, and...
  21. Craig Nedrow

    BBC 489 build

    Nice enough today to work on the doner truck, so got the body off. It is remarkably straight, with two good doors. Plan is to completely strip it down, taking lots of pictures. I plan on removing most of the exterior and interior paint, then fix any rust, imperfections. Somebody put three screw...
  22. Craig Nedrow

    BBC 489 build

    port matching. steps: blue and scribe, second pic is hogging out, port on right is complete.
  23. Craig Nedrow

    Granger Smith aka Earl Dibbles Jr. father's 74 GMC full restoration videos.

    Watched all 23 episodes, but fast forward quite a bit. Interesting, he quit music, got busy in his local church, and is going to school studying theology. He lost a child I learned, hate to think about it, but he's headed in the right direction for sure.
  24. Craig Nedrow

    BBC 489 build

    Cleaning, painting all the front end accessories. For now, I will use the old system, but may change if those darn vee belts squeal, hate that. Ok for girls though....just sayin'. Here is the engine at end of day.
  25. Craig Nedrow

    BBC 489 build

    Manley push rods, very nice, weigh 73, and 83 grams each. I did not have any interference with rockers to valve cover. All studs torqued 45 ft lbs, guides adjusted, and tightened. Lash is .035 down from 0 backlash, so I went to 7:00 o'clock. Soaked the Johnson lifters B-4 installing. Shot brake...

Latest posts

Forum statistics

Threads
45,299
Posts
980,143
Members
38,312
Latest member
bbbbyffff6
Top