Search results

  1. 8T6K5

    AC Delco Plug Wires

    You can never go wrong with RA..... Sent from my iPad using Tapatalk
  2. 8T6K5

    Thoughts on a 4" suspension lift?

    Raised steering arm, T case drop.... Sent from my iPhone using my iPhone
  3. 8T6K5

    35" tires 4" Body Lift

    Zero-Rates = 1" ...plus 1" ORD BL I have 35's on my K5, 4" springs and zero-rates.....will goto 1" BL when I step up to 37's http://www.offroaddesign.com/catalog/Zero%20Rates.htm DIY4X has the same thing...called EZ-inch
  4. 8T6K5

    What is it...

    So here it is; 3 wire heated o2.... With the harness install is a snap. Could easily be wired without on your own, Im just too lazy and prefer "plug and play". o2 sensor into the harness, OE connector to harness connector...pink to 12v and black is ground. PN for the 3 wire...
  5. 8T6K5

    3" Body Lift Question

    For a 3" I think you will need steering and trans spacers too... Why do you need a 3" BL?
  6. 8T6K5

    35" tires 4" Body Lift

    4" body lift....??? :doublepuke: Try ORD or DIY4X zero-rate's and/or ORD 1" body lift.
  7. 8T6K5

    Bvllsh!t on craigslist.

    Now, gettin' to Texarkana and back in 28 hours, that's no problem... http://phoenix.craigslist.org/evl/cto/3600057466.html
  8. 8T6K5

    Multi-Port EFI discussion...

    Im far from experienced here either and like you, the more I read, the more I get cornfused. I have a TPI 350 now that will be needing a rebuild soon. Yes, the TPI, designed for a 305, isnt suited for a high rev'ing application. Depending on mod's will die around 4500rpm's.....perfect for...
  9. 8T6K5

    What is this???

    Also looks like a severed vac line coming out of the firewall.....
  10. 8T6K5

    What is it...

    You just won your first Rep point.... :winner_first_h4h: o2 sensor should be in today. Pretty much plug and play, then off to emissions for the true test. Benefit of a heated o2: http://www.cfm-tech.com/oxygen_sensor_tuning.htm Important information on the two different types of...
  11. 8T6K5

    What is this???

    ????
  12. 8T6K5

    What is it...

    The part that this harness adapts to is due in later today... until then lets see what GMSQB thinks...
  13. 8T6K5

    What have you done to your square lately??

    Mounted my Mic.... sometimes it's the little things: Also, comparing Old v New:
  14. 8T6K5

    New Battery Cables, No Power

    That ground should go to either the frame or the engine block....
  15. 8T6K5

    Installed lift kit but front lower

    ORD-DIY4X zero-rates.... Sent from my iPad using Tapatalk
  16. 8T6K5

    What have you done to your square lately??

    CB mounted: PA speaker mounted: Still not sure where Im gonna put the speaker. Would prefer it to be out of sight- out of mind: No antenna yet...not sure where Im mounting that just yet???
  17. 8T6K5

    What have you done to your square lately??

    Custom Check Engine light.... :)
  18. 8T6K5

    What have you done to your square lately??

    Put a few miles on it...went Mall Crawlin' :) Aside from some major blow-by out of the dip stick and a harder 1-2 shift than I remember....feels good. Steady oil pressure, temps <210*, idle is ok...could probably be tweaked
  19. 8T6K5

    "The Big 3 Upgrade"

    Just added the final piece to this mod: CS144 140A alternator: Volt meter at idle, with just Big 3 mod: Volt meter at idle with Big 3 and CS144: Holding about 14v at idle.
  20. 8T6K5

    What have you done to your square lately??

    Did both times, which is why Im a little cornfused. Somehow just were'nt seating right...
  21. 8T6K5

    What have you done to your square lately??

    I think I need to wrench with a hangover more often.... Woke up this morning and jumped back into the engine. I pulled the injectors again to find this...the #7...again: Pinched O-ring... Pulled the fuel rail for inspection....looks OK to me. Replaced the O-ring and re-installed...
  22. 8T6K5

    What have you done to your square lately??

    ......that was the easy part of my day. After we get that sorted out and everything buttoned up I go to start it..... ....and fuel is just spewing out from around the #7 injector and Im like WTF! Friend splits and I just cant stop wondering why. So I get down to the fuel rail, pull...
  23. 8T6K5

    What have you done to your square lately??

    Just couldnt catch a break today. Started with this: Left me with about 3-4 threads showing. The red tape on the other bolt represents about how much was in the manifold. If I had a welder Id just thread a nut on and put a weld and hopefully pull it out. I dont, so I was able to get...
  24. 8T6K5

    Homebuilt Hitches

  25. 8T6K5

    Bvllsh!t on craigslist.

    :think: http://phoenix.craigslist.org/cph/cto/3570554739.html

Latest posts

Forum statistics

Threads
44,617
Posts
962,642
Members
37,158
Latest member
thom9719
Top