Search results

  1. AKguy

    Nasty Noise Coming From Flexplate/Converter area

    Just saw 1987 Jimmy’s similiar post and it sure sounds like cracked flexplate!
  2. AKguy

    Nasty Noise Coming From Flexplate/Converter area

    1985 K20 Suburban, 350/700R4, 14” 168 tooth flexplate, three bolt converter. When warm/hot, about 90 here today, getting fairly loud, tinny/grinding noise while parked and in motion. Looked at starter intereference, none I could fine, put different starter on, no change. Truck is shifting as it...
  3. AKguy

    Can someone tell me about this truck! Never seen before...

    Could be like the YH4 code used for special or seasonal packages of different types.
  4. AKguy

    Can someone tell me about this truck! Never seen before...

    Saw a post somewhere that an S10 or S15 had the same code.
  5. AKguy

    Which wiring harness

    I have had great success with American Autowire. Did a complete update kit for my daughter’s Chevelle, and all but the dash harness on my K30.
  6. AKguy

    Have to store outside. Truck Cover?

    I have found that covering the vehicle does more harm than good, even in Alaska.
  7. AKguy

    My new 83 k30

    I installed the sniper on my recently rebuilt 454. The installation is straightforward, but you will need to invest some time in getting it dialed in. I am still working on a decent idle, but once you get her going it runs great. My handheld display quit about 3 weeks into using it. Holley fired...
  8. AKguy

    Engine threaded bosses

    Have never installed the pivot stud, so do not know.
  9. AKguy

    Engine threaded bosses

    Seems I have seen clutch pivot studs mounted in those holes, either fore or aft.
  10. AKguy

    Switched Power for Electric Fan Relay

    I cheated and used my Holley Sniper trigger leads, but I cannot see why the choke feed would not work well.
  11. AKguy

    New Kick Panels

    I see Auto Metal Direct is advertising these now.
  12. AKguy

    1977 C & K Model Wiring Diagram

    Love those! I have them for my 81 and a 79 F250
  13. AKguy

    Transfer case support bracket

    I had to use some washers between the face of the rod and the bell housing hole to make up about a 3/8” gap. I could have modified the holes at the transfer case end (NP205) but the washers seemed reasonable.
  14. AKguy

    Is there any hope for these tools?

    Hydrogen Chloride of at least 20%. I use stuff called Poly-Zag, toilet bowl cleaner. Amazing stuff, but use it outdoors, with a respirator.
  15. AKguy

    Winch Bumper wanted!!

    Anybody know if this guy is still in business? Sent an e-mail about a week ago and have not received a response.
  16. AKguy

    Insulation on a Budget

    Used this stuff. Seems to work well, got it from Amazon.
  17. AKguy

    Good resource for 9+1 Rear Leaf Springs?

    Was not bad and they were great to work with.
  18. AKguy

    Good resource for 9+1 Rear Leaf Springs?

    Murphy’s Frame and Axle!
  19. AKguy

    Lens Retainer

    It is plastic. Shoot me your address and I will get it off to you.
  20. AKguy

    Lens Retainer

    This work? From a 1980
  21. AKguy

    Need Resources

    My pleasure.
  22. AKguy

    What have you done to your square lately??

    Needed something above the blacked out badges. Alaska flag.
  23. AKguy

    Looking for AM/FM Radio

    No problem, I’ll put it back on the shelf.
  24. AKguy

    Overdrive Trans or Ring and Pinion swap?

    I plan to install a Gear Vendors unit in the spring, even after swapping my 4:10s to 3:73s.
  25. AKguy

    Looking for AM/FM Radio

    The connector is not there.

Latest posts

Forum statistics

Threads
44,411
Posts
956,917
Members
36,731
Latest member
LucHiscox98
Top