Search results

  1. AKguy

    Electrical and Harness Repair Parts

    I cannot give enough praise to the folks at American Autowire. I used their complete upgrade kit for my daughters 1969 SS 396 Chevelle, and I just received a replacement engine harness for my 80/81 C20 to K30 project. Their products and support are incredible. Yes, they are not inexpensive, but...
  2. AKguy

    78 K-10 Dual Tank Install

    The folks at EFI System Pro can hook you up.
  3. AKguy

    I want a rear sliding window!

    side by side
  4. AKguy

    I want a rear sliding window!

    Just saw the post, will hang a pic this evening
  5. AKguy

    I want a rear sliding window!

    I just received my new C.R. Lawrence slider after having to cut out my factory slider and finding out seals are no longer available.
  6. AKguy

    4x4 Crewcab weight

    According to factory specs on the 1981 K30, the curb weight was listed as 6264.
  7. AKguy

    Factory Rear Slider Seal

    Issue solved. Ordered new, aftermarket model that uses the standard seal.
  8. AKguy

    Factory Rear Slider Seal

    I am finding new rear window seals, but none that advertise they fit the factory slider. Have found one that says it fits the aftermarket windows. Anyone faced this situation before? Factory and aftermarket seals the same? Thanks.
  9. AKguy

    Leaf Spring Options

    These guys built me new springs to replace two broken springs for my K30. They were fast and reasonable, especially when shipping to Alaska. Murphy’s Frame and Axle 513 Wood Street, La Crosse, WI 54603 :: Phone: (608) 782-2817
  10. AKguy

    Sending unit ports

    Cool, yeah, Sniper recommends 3/8”, EFI Sustem Pros suggest 5/16” returns, so I think I will just use the factory 5/16” for vent and use the AN 3/8” thru fittings for the returns. Thanks. Edited to correct info.
  11. AKguy

    Sending unit ports

    Okay, received two new units for my main and aux saddle tanks, Spectra FG05H models that will be feeding/returning from, my Sniper EFI. They have two ports, one 3/8 for the supply and a 5/16. Is that 5/16 intended for the return? If so, will I need to vent them like the originals that had a 1/4...
  12. AKguy

    Street Warrior/Sniper EFI combo hood clearance

    For those of you running the 8122 Street Warrior manifold topped with a Sniper EFI, or carb for that matter, on your big block, how much room you have remaining for the air filter? Thanks.
  13. AKguy

    Rear Disc Brake Plumbing

    Perfect! Thank you!
  14. AKguy

    Rear Disc Brake Plumbing

    Okay, 1980 K30. I have the new rear disc brakes mounted on the 14 bolt full floater and am ready to plumb. I used the same calipers as on the front and they have M10-1.5 threads where the banjo bolts normally go. I would like to run hard lines all the way to each caliper. As an option, I could...
  15. AKguy

    Does anyone sell new seat covers for these?

    Contact Wet Okole, the best neoprene covers I have found. They will want many pics and measurements, and they are expensive, but worth every penny.
  16. AKguy

    Cab Marker Lights

    When it is snowing, foggy, etc., I like to see as many lights as I can.
  17. AKguy

    Cab Marker Lights

    Thank you!
  18. AKguy

    Cab Marker Lights

    Looking for input on replacement amber marker lights that fit the roof contour of my 1980 Crew. Have a set of Ford ractory replacement but the holes necessary to mount them for the connector are hideously large.
  19. AKguy

    Tack weld or no tack weld for oil pick up to pump.

    If you TIG it with silicon bronze rod you will keep the heat lower.
  20. AKguy

    Dana 44 Steering Damper Mount Location

    Okay, I found a couple rigs to measure and on both the Dana 44 and 60 the center of the mounting bracket hole is about 5 1/4” from the housing. I’m sure everyone here was on the edge of their seat.....
  21. AKguy

    Denny’s Driveshaft

    I don’t know how many of us on this, and other forums, live outside the “Lower 48 States”, but those of that do know all too well the woes that can be encountered when having items shipped to our locales. Denny’s Driveshaft will ship via flat rate USPS which is a big savings, e.g., $8.50 versus...
  22. AKguy

    Partial VIN frame - can anyone read this

    That’s my guess.
  23. AKguy

    Dana 44 Steering Damper Mount Location

    I have a 1973 Dana 44 front differential that was bolted to my 1980 K30 Crew. The inside, near the housing, damper mount is a hokey bolt-on affair that, 1. I want to make a weld-on replacement for and, 2. I need to know the distance from the housing, or other reference point, and distance below...
  24. AKguy

    Spicer 44 Bushing Needed

    Perhaps, I will reach out and see if it can work for my application. Thanks!
  25. AKguy

    Spicer 44 Bushing Needed

    My 1975 dated Dana 44 still has the Spicer 44 hubs and they are in great shape, except for one of the bushings ( item 17 ) that the inner clutch gear rides on is toast. Have been searching e-bay, etc., and have not found one. If any y’all got a line on one it would be greatly appreciated.

Latest posts

Forum statistics

Threads
44,411
Posts
956,917
Members
36,731
Latest member
LucHiscox98
Top