Search results

  1. MikeB

    2001 YZ 250

    I used to ride motocross and cross country back in the 70s-90s. We always said, "There is nothing more used than a used dirt bike." And we were talking about 2-3 year old bikes! That said, a buddy of mine has a 96 WR250 (cross county version of YZ) that's in pristine condition. But I doubt...
  2. MikeB

    Bulkhead / Firewall Connector

    Good luck finding new connector halves. After looking for a while, I gave up and bought an aftermarket harness. One of the benefits was larger gauge wires for just about every circuit.
  3. MikeB

    First Ever K-10 Build, What’s It Worth??

    Probably won't be worth as much as you put into it, unless you do all the work yourself. Body, paint, and interior can get expensive in a hurry when you're paying pros to do it. I'd guess that I have $9K total in mine, and did all the work myself except for front end alignment and machining...
  4. MikeB

    Th350 MPG question

    I had a TH350C in an 81 C10 back in the late 1980s. It tended to lock-up too soon under steady throttle (as low as 35-40 mph) which caused the little 305 to literally shudder. It was especially bad with the 2.56 axle. I learned to drive around in 2nd gear until I hit the highway, but even...
  5. MikeB

    Leaf Spring

    If you ever need new springs, these guys have good prices and service: https://www.truckspring.com/Search.aspx?p=Make:Chevrolet/Year:1982/Model:C10/Suspension-Parts/Leaf-Springs
  6. MikeB

    15 inches of vacuum

    That's a good idea. So many of the vacuum cans have 20" or more, which is "clatter" waiting to happen as you lightly roll on the throttle. Most guys will simply back off initial timing a bit to get rid of the clatter, but that is NOT the answer because it hurts performance. I found a...
  7. MikeB

    15 inches of vacuum

    Yes. That's because engine vacuum is relative to atmospheric pressure. So, the lower the atmospheric pressure, the smaller the difference between that and engine vacuum. Engine vacuum decreases about 1" hg for every 1,000 ft above sea level. So, a 350 that makes 20" hg in Houston would make...
  8. MikeB

    Heavier Duty Coils on 2wd. Any issues?

    I guess it depends on which springs your truck has now. If it has the basic C10 suspension, Moog #6452 would be the OE replacements, but they have a little higher spring rate (843 lbs/in) than OE. Moog's spring chart shows the #6454 spring rate is 1060 lbs/in (25% stiffer than #6452), which...
  9. MikeB

    1980 z28 rescue

    T10 behind a 454? Be careful! Can't believe you got so much done in 5-6 weeks. Great job!
  10. MikeB

    Hi from TX

    I was just looking on the Internet and found that descriptions of clamp-on multi-meters are fuzzy at best. Many of the so called AC/DC clamp-on meters measure only AC current with the clamp, so make sure you know what you're getting. Also, you want one that measures as little as .01 amps. I've...
  11. MikeB

    BEFORE AND AFTER UPDATE

    That looks very nice! Funny but I just finished machine-polishing my 82's original almond paint (light tan) with a random orbital polisher. I'm in the process of waxing it now. Poor thing spends most of its time outside, but we're building a house with a 32' x 25' garage!
  12. MikeB

    Under hood wiring - Part 1

    This might help a little. Not OE, but I think the colors are the same. https://www.americanautowire.com/pub/media/productattachments/files/downloads/92970190 510348 IN 2.0.pdf
  13. MikeB

    Did I get the right jack stands?

    I wouldn't worry about shape, but the height of 3-ton stands is too low for a pickup, IMO. I have 2 pairs of 6-ton stands and one pair of 12-ton. Can't beat those 12-ton models under the axle tubes for getting the truck up in the air! I think you'll find the 3-ton models will need to be...
  14. MikeB

    305 build advice. Any and all advice is appreciated!

    Pulling the axles is the easy part! Changing the ring & pinion is not a trivial task. I've done two 10-bolts and one 12-bolt. Made a couple of mistakes on the first one, but got them corrected right away, and felt more confident doing the last two. You will need a 12-ton press (or better yet...
  15. MikeB

    Help picking spark plugs.

    For those who have problems with plugs lasting a long time: How do they fail? Eroded electrodes, oil-fouled? In my experience, Bosch platinum plugs (single electrode) last a long time with GM HEI distributors --either stock or with MSD module & coil. I have no idea why they wouldn't work for...
  16. MikeB

    vinyl floor replacement help/opinions wanted

    Forgot where I bought my vinyl floor cover, but it covers the entire floor with jute padding running back to the front of the seats. I had to trim it a lot at the front, but better that than not enough material. Recently, I actually replaced the jute padding with insulation (The Insulator) on...
  17. MikeB

    Question about vintage air

    Kick panel vents aren't affected if you get the kit for non A/C trucks. I would sure shop around. But no matter who you buy from, V/A will give you great tech support.
  18. MikeB

    Anybody use this magnum cam set

    That appears to be the old Magnum 270 cam. 224/224 is too much duration for a truck with stock heads, compression, and gearing. That cam would probably like 10:1 compression and somewhere around 3.73 gears. These are from Comp's High Energy family and would be much better choices...
  19. MikeB

    Best Front-end Rebuild Kits

    Sad to hear. I've been on that forum for >20 years, and although they have more members who own earlier trucks, I still get help there with 73-87 issues.
  20. MikeB

    Best Front-end Rebuild Kits

    Rubber bushings flex kind of like a torsion bar. Poly bushings don't. They would break if they did! Instead, the outside of the bushing is essentially pressed in the A-arm, and a shaft sleeve rotates in the inner hole.
  21. MikeB

    Converting ash tray to audio controls

    As for radio and speakers, someone gave me an old NOS Alpine brand new in the box.Ended up cutting the dash, but now wish I hadn't.:( Speaker is a RetroSound 4x10 with two voice coils for L and R radio outputs. It sounds OK for news and sports talk, but I will probably add 6x9s in cab corner...
  22. MikeB

    Converting ash tray to audio controls

    I replaced the ashtray with an insert to fit an iPhone. Still have to select a USB charger. Looking at one that displays voltage. Only about a couple hundred to choose from!
  23. MikeB

    79 250 integrated head exhaust manifold crack

    For those who may eventually need to replace a cracked integrated head: https://www.shop.headsonly.com/GM-CHEVROLET-250-INTEGRATED-REBUILT-CYLINDER-HEAD-GM-250-INTEGRATED.htm
  24. MikeB

    Best Front-end Rebuild Kits

    That's what I used along with liberal amounts of the included silicon lubricant. I think steering response is much better, even compared to new rubber bushings. Some folks say poly bushings squeak, but I've never had that problem with them in my 82 C10 or my 55 Chevy car. I've also used...
  25. MikeB

    Best Front-end Rebuild Kits

    In my experience, KYB Gas-A-Just shocks are MUCH better than basic Monroe or Gabriel, and will last longer -- around 12-15 years on my son's 69 C10. The Excel G is KYB's OE-replacement shock, and they've been working on my own 82 C10 for 4-5 years. They're actually still a little stiff...

Latest posts

Forum statistics

Threads
44,400
Posts
956,649
Members
36,709
Latest member
85squarebody805
Top