Search results

  1. Obwonkonobe

    Fuel Pump- Mechanical or Electric

    Dude hook that AC up! Also, I always like to run a mechanical for simplicity, but il keep one of those cheap little electric ones in the truck for when the mechanical goes out 30 miles away from the shop. Ask me what made me start doing that..
  2. Obwonkonobe

    Engine code identification

    Oh alright thank you, good info
  3. Obwonkonobe

    Brake lights

    Since you have them signals your grounds should be good then btw, just to rule things out
  4. Obwonkonobe

    Looking for opinions on Lowering Kits

    Funny thing is, my bed is already notched. That and the new stock front coil springs makes me thing this thing was lowered at some point, but the po stole his drop springs and shackles before selling it
  5. Obwonkonobe

    Engine code identification

    Thanks that site will help. I just tried to check but its too hot. Il get a better look one morning when things aren't hot
  6. Obwonkonobe

    Engine code identification

    Il poke around some more soon and report back, thank you
  7. Obwonkonobe

    Engine code identification

    Oh weird, is there another location I can check?
  8. Obwonkonobe

    Engine code identification

    My bad, service was bad and pic didn't upload
  9. Obwonkonobe

    Engine code identification

    I snagged this pic a while ago, its the front passenger pad that should have the engine code. Although when I try to use typical decoders it doesn't match up. It had goodwrench 350 valve covers when I bought it so I assume its not original. I just wanna be sure its a 350 and see when it was...
  10. Obwonkonobe

    700r4 stacked shifts

    Ive got one with a clamp to get you close, then you press a button and move the body to adjust. I'd say as long as you know what you're doing you'll be ok. Just be sure it stays in place, I'm not sure if id trust it unless it has a way to keep it clamped in adjustment
  11. Obwonkonobe

    Dash Light Issue

    I had to go through and map out all those little pins in the bulk connector for the gc. Then pull then out and re pin it. That's because the po put in a different year and style gauge cluster
  12. Obwonkonobe

    Source for 74-80 heater control

    It should just be a cable that you pull on. If its truly a beater, rig a bicycle brake cable to it and run it to the cab, then you can actuate it by pulling it and pushing it in the housing
  13. Obwonkonobe

    Second Trans failure in 200 miles

    If you have a 9 inch tailhousing on the 350, the drivshaft will swap. That's how I did mine
  14. Obwonkonobe

    Front end alignment?

    If you've never adjusted it before as well, there's a nut and bolt inside it on the top of the gearbox, that allows you to tighten up the steering. Its just a bandaid if you have other issues, but cant hurt. Just be sure to go in 1/8 to 1/4 inch increments on the center bolt, the nut is just...
  15. Obwonkonobe

    Looking for opinions on Lowering Kits

    Does anyone have any opinions on shackles? I have a stock height 78 on 31s and have been considering grabbing some 2 inch lowering shackles to level it out
  16. Obwonkonobe

    tach

    I have a v8 and want a tach too, do you know of a way to convert between the 2?
  17. Obwonkonobe

    Rustiest Radiator Thick Slimy RUST... How To Clean???

    I don't mean to hijack the thread, but what kindof mileage were you getting with a 700 and 3.08s? That's the same setup I have now, just curious
  18. Obwonkonobe

    Prepping for 700r4 goodness

    I think so, its just the slotted c shaped bracket
  19. Obwonkonobe

    Prepping for 700r4 goodness

    To anyone else doing a trans swap(just in general because im sure others are like this too), swap the old c looking thing for the gear selector too. I sealed over the old one from my 350 just now and it made a world of a difference, i can hit every gear easily now. No weird angles like before...
  20. Obwonkonobe

    454 knock - looking for suggestions

    If you have the means, I'd tear it down and give it a BASIC rebuild, maybe toss in a new cam/lifters and defiantly bearings. If it runs good other than the knock I wouldn't touch anything else
  21. Obwonkonobe

    Pioneer box replacement speakers

    The pic is a bit hard to see but That's How I did my door speakers. Mines 78 too but my door panels are shot so I didn't feel bad about hacking them.
  22. Obwonkonobe

    Prepping for 700r4 goodness

    Youll probably see a couple degrees difference, and sure it's something but if you're chasing a couple degrees to keep your stuff cool enough, you've got bigger issues. That being said though knowing this il probably never paint a radiator lmao
  23. Obwonkonobe

    Pioneer box replacement speakers

    Where do the boxes mount, rear cab corners? I just run 2 50w 5.5 inch speakers with built in tweeters in my doors. That and a 300w sub behind the seat is plenty for our trucks. If they're for the cab corners I might put 2 more in the doors or kick panels, im just not sure how much your seat...
  24. Obwonkonobe

    "Rebuilt" 700r4 issues

    @Splandman great explanation thank you! So its basically a mechanical lock up, I like the sound of it
  25. Obwonkonobe

    TH350 problems

    That means that the problem is with your clutches inside the trans. If you have no reverse I'd be happy, you may just need a torque converter

Latest posts

Forum statistics

Threads
44,173
Posts
950,868
Members
36,288
Latest member
brentjo
Top