Search results

  1. spanky55amg

    I need a seat ID please

    I always think that finding someone to recover would be expensive, but everyone's story seems to be the complete opposite. They sometimes are cheaper than pre-made generic covers and always look a whole hell of a lot better.
  2. spanky55amg

    Need some recommendations

    $200 total? none. check ebay and craigslist.
  3. spanky55amg

    C10 Nationals May 3-5 2018

    https://c10nationals.com/ This is in the Dallas / Fort Worth Area.
  4. spanky55amg

    Welder

    Im almost 37 and wished I knew how to weld. If youre 15 years old and have the time now... learn to weld!!! There is so much you can do with welding, even if you do it has a hobby. But you will prob use it more for yourself. Places still pay good money for people that can weld. Its one of the...
  5. spanky55amg

    Ball Joints/Tie Rod Ends What Brand????

    http://proforged.com/ Have you checked them out. I know we were talking in the rant forum about them. I know it sounds bad in the rant forum, but we werent bitching about them. Start here http://www.gmsquarebody.com/posts/371674/ but like I said, we werent bitching about them, but we all dont...
  6. spanky55amg

    mileage question

    See, there is no reason this C10 305/700r4 isnt getting 15+. I expect 15 at least and hoping for 18. grrrrrrr.
  7. spanky55amg

    mileage question

    shite, you changed your pic.... and thanks ass! :)
  8. spanky55amg

    Digital Dash

    Someone on the forum runs them too. Or brought them up before. You can pick what color of LED's you want too. If I ever go digital, it will be them, but Im a sucker for analog.... unless its a speedo.
  9. spanky55amg

    mileage question

    I have mine set to 10. I put this leaking (not leaking after I removed it and put in a new accelerator pump) holley double pumper. Gah, this truck runs great now. I just want this q-jet to be fine. Pulling it off, it looks like the power valve isnt correct either as the horn gasket is soaked in...
  10. spanky55amg

    mileage question

    question... The rebuilder says that my 5-8 mpg issue is that it had 74-76 metering rods and that it should be 70. This carb: spits, sputters, doesnt want do over 3000 rpms, bogs, dies, doesnt start or idle correctly, and just plan runs rich. All of the issues happen at any rpm. Do you think...
  11. spanky55amg

    The Bench Seat...

    Damn thats nice. Im still looking for an 81+ bench to rebuild. Its that or Im spending $1000 just for aftermarket stuff and I kinda of like factory.
  12. spanky55amg

    Online Source for Factory Replacement Rally Wheel Center Cap Screws

    If this were ebay, I would give you an A+++++++++++++ Instead, :cheers: Also, here is my hardy handshake...:handshake:
  13. spanky55amg

    lowering shackle install

  14. spanky55amg

    Reman AC compressor 57235 junk?

    You could be right. I have never ever done AC outside, so I never worried about the temp. And all work I have done were on newer MB's. Id always like to see 250-275. But I guess first, I'd like to see that low side below 50 and the closer to 40 the better.
  15. spanky55amg

    Reman AC compressor 57235 junk?

    In my years of being a tech, its either a bad compressor or the freon level isnt correct. Are you using R12 or 134A? You said you have a new expansion valve and dryer. I havent replaced mine yet, but from the sounds of it, a lot of these compressors make noise. But after running for 5 minutes...
  16. spanky55amg

    NEWBIE

    Welcome! She looks clean.
  17. spanky55amg

    Just saying hello

    As much as Honky asks for pics... pic related. Welcome to the site!
  18. spanky55amg

    just tinted, what do ya think?

    Im hiding mine... hahahahahaha
  19. spanky55amg

    just tinted, what do ya think?

    for $13 bucks and peel off.. I could deal with a crappy tint job. You havent seen the rest of the truck. That picture is cropped for a reason.
  20. spanky55amg

    e320 wagon

    Yeah, some of the early 210s didnt have head rest release buttons. And youre missing seat heater buttons too. :) haha. What was nice about MB back then, you could get cherry pick options. About 2003 ish, they stopped doing that and came out with packages. Damn, ASR. I would have thought that 98...
  21. spanky55amg

    New to me 83

    Welcome... digging the colors!
  22. spanky55amg

    Proud new owner here...

    Since the Texas guys are showing up in herds... Welcome from the Big D, Dallas!
  23. spanky55amg

    newbie

    Welcome!
  24. spanky55amg

    First time caller...

    Welcome... Creeper McCreeperson ... haha
  25. spanky55amg

    Favorite tool brand?

    My first box was a used old Matco box that I bought off of the truck, right time, right price. I was just starting out and still working out of my Lincoln Tech red metal portable toolbox. $600, on truck credit and he would take whatever I could afford that week, no questions asked. But if I...

Latest posts

Forum statistics

Threads
44,173
Posts
950,868
Members
36,288
Latest member
brentjo
Top