CARBURETOR DATED

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

boloboss

boloboss

Full Access Member
Joined
May 6, 2023
Posts
72
Reaction score
19
Location
Houston Texas
First Name
Shuntel
Truck Year
1984
Truck Model
Chevy C10
Engine Size
v8 350 5.7 liz6er
My timing was initially set at 4° and I turned the distributor just a smidge it to advance it
 
Vbb199

Vbb199

B-rate Hillbilly Customs
Joined
Jan 12, 2018
Posts
9,108
Reaction score
15,456
Location
Salisbury NC
First Name
Vince
Truck Year
89, 79
Truck Model
89 Suburban R1500, 79 C10
Engine Size
350, 502
Seems like theres potential the timing could be retarded too much and its causing your issues with not wanting to start back up after being ran a while
Try 8 or 10° and see if it does it anymore
 
Vbb199

Vbb199

B-rate Hillbilly Customs
Joined
Jan 12, 2018
Posts
9,108
Reaction score
15,456
Location
Salisbury NC
First Name
Vince
Truck Year
89, 79
Truck Model
89 Suburban R1500, 79 C10
Engine Size
350, 502
That might necessitate enrichening your idle mix a little also, but perhaps not
 
ali_c20

ali_c20

Full Access Member
Joined
Sep 20, 2016
Posts
1,346
Reaction score
1,949
Location
Austria
First Name
Alexander
Truck Year
1974, 1979
Truck Model
C20, K5
Engine Size
350, 350
I run 12 degrees on my K5 and 14 on the 66 Impala.
Always be sure your ignition system is working as it should before fiddling with the carb.
xc_hide_links_from_guests_guests_error_hide_media

Search Uncle Tony's Garage on youtube, this guy knows tons about carbs and ignition and all the other stuff.
He's a Mopar guy but the principles are the same for all engines.
 
G

Generalmoto

Junior Member
Joined
Feb 6, 2024
Posts
2
Reaction score
3
Location
canada
First Name
Josh
Truck Year
1977
Truck Model
C10
Engine Size
350
slammed84 said:
I was having this same issue over the HOT summer, initially thought it was because I swapped in a metal cased Wix fuel filter.

Ended up being the ignition module crapping out a few times before finally failing for good.

Next time the issue is happening, check to see if you have spark from the plugs, if not, swap your ignition module
Click to expand...
I had weak performance for a year couldn’t figure it out until I pulled a plug and looked at the spark. Was weak and yellow instead of blue and crisp. Changed the coil and big difference.
I agree those ignition issues slowly sneak up on you
 
S

SmokinB

Junior Member
Joined
Feb 3, 2018
Posts
2
Reaction score
1
Location
Oklahoma
First Name
Scott
Truck Year
82
Truck Model
Silverado K10
Engine Size
350
boloboss said:
What's up guys?
I have a 18 -year-old 1406 Edelbrock carburetor that's been rebuilt twice. Ot stars right up in the morning, no problem......but, I've been having issues with it not cranking right up after I've driven it for 30 minutes, let it sit for while, then try to start it up again... and after that, if I turn it off and start it up again it cranks right up .Do you recommend me buying a new one or rebuilding it again? And if I buy a new one, what carburetor do you recommend? I have a 350 small block in a '84 Chevy C10
Click to expand...
I have the same issue. The fuel is getting too hot. Use a carb spacer that will insulate - and block off the crossover directly beneath the carb if possible.
 
AuroraGirl

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,693
Reaction score
6,875
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
Vbb199 said:
Seems like theres potential the timing could be retarded too much and its causing your issues with not wanting to start back up after being ran a while
Try 8 or 10° and see if it does it anymore
Click to expand...
You must be registered for see images attach

boloboss said:
Ok
Click to expand...
op can you show me your distributor with the cap off like this picture here?
 
boloboss

boloboss

Full Access Member
Joined
May 6, 2023
Posts
72
Reaction score
19
Location
Houston Texas
First Name
Shuntel
Truck Year
1984
Truck Model
Chevy C10
Engine Size
v8 350 5.7 liz6er
Also, will covering up the crossover on the carburetor intake reduce the overall temperature of my engine
 
MikeB

MikeB

Full Access Member
Joined
Apr 4, 2014
Posts
1,782
Reaction score
1,020
Location
North Texas
First Name
Mike
Truck Year
1969
Truck Model
C10
Engine Size
355
More than likely, intake manifold heat is causing the gas to evaporate. Try raising the float level above spec for starters. The owners manual tells you how to do it. Also try a phenolic spacer at least 1/2" thick.

I'm having a similar problem with an old 1406, that otherwise works perfectly. Unfortunately I won't be able to continue troubleshooting until the ambient temps get back up into the 90s. I've got my eye on an AVS2, but I'd like to hear from the guys that have one, because the float bowls are still in the same place--way down low close to the manifold. A Holley or one of the clones like QuickFuel or Brawler shouldn't have a problem because of float bowl location. Or at least not as much of a problem.
 
Sad Sack

Sad Sack

Junior Member
Joined
Sep 3, 2024
Posts
7
Reaction score
7
Location
Omaha, NE
First Name
Bryan
Truck Year
1985
Truck Model
C15
Engine Size
305
Just a random thought but has anyone considered a drain-back issue?
 
R

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,595
Reaction score
9,108
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
Sad Sack said:
Just a random thought but has anyone considered a drain-back issue?
Click to expand...
Not a possibility on an Edelbrock 1406,due to location of fuel inlet and needle and seat. 2 like these should stop your fuel boiling. If that's the problem
 

Attachments

  • Screenshot_2024-11-04_164111.jpg
    Screenshot_2024-11-04_164111.jpg
    55.4 KB · Views: 10
  • Screenshot_2024-11-04_164035.jpg
    Screenshot_2024-11-04_164035.jpg
    54.2 KB · Views: 13
Last edited:
AuroraGirl

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,693
Reaction score
6,875
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
Ricko1966 said:
Not a possibility on an Edelbrock 1406,due to location of fuel inlet and needle and seat. 2 like these should stop your fuel boiling. If that's the problem
Click to expand...
wdym not possible?
 
You must log in or register to reply here.

Similar threads

boloboss
Carburetor Issues
Replies
1
Views
250
Snoots
Snoots
YardPickerUpper
The Best Carburetor?
2 3
Replies
33
Views
3K
Turbo4whl
Turbo4whl
boloboss
350 small block
2
Replies
16
Views
1K
Jimmyperf400
J
hey mister
Quadrajet Primary Shaft Bushings
2 3 4
Replies
57
Views
2K
Ricko1966
R
legozombie
Engine Stalling - Bad EVAP/Charcoal Canister?
2
Replies
29
Views
4K
legozombie
legozombie

Latest posts

Forum statistics

Threads
44,411
Posts
956,919
Members
36,732
Latest member
blackmfcowboy
Top