Rebuilding my dash pad.

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Chris64

Full Access Member
Joined
Sep 16, 2024
Posts
80
Reaction score
110
Location
San Diego
First Name
Chris
Truck Year
1974
Truck Model
K20
Engine Size
350
OK, A new project that probably won't work, but I'll try. I figure worse case scenario, I just buy a whole new dash.

My original plan was to fill in the cracks and to fiberglass it as others have done. It looks good but I wasn't in love with it versus the more natural looking grain as well as being soft. Regardless, the factory dash foam was peeling away from the metal in areas where the windshield was likely leaking and rust was forming underneath. These areas are beyond salvaging without some major surgery.

I used to do a lot of custom interior parts in the 90's like wrapping custom speaker pods in vinyl so I don't know why that won't work here.

I did a test on a small technical area around a mounting screw and it looked great so let's see how it goes on the whole dash.

A few questions for all the square-body brains here:
1) Is there a chance the foam has asbestos in it? My son asked me that and NGL I can't get it out of my head.
2) does that middle speaker need to be there for any ventilation reasons? I was thinking about maybe putting a couple tweeters right and left to bounce off the windshield but didn't really need a center speaker. I can perforate the vinyl to look stock which would look really cool, but it's also a lot of extra work and years of sun will wear on it.

I plan to wear a respirator even if it's foam but if it's asbestos, I'd probably just ditch it.
You must be registered for see images attach
 

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
30,637
Reaction score
28,926
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
It's just foam. The center opening was only for the speaker, so it won't hurt anything at all if you choose to cover that area.
 

Grit dog

Full Access Member
Joined
May 18, 2020
Posts
7,105
Reaction score
12,513
Location
Auburn, Washington
First Name
Todd
Truck Year
1986, 1977
Truck Model
K20, C10
Engine Size
454, 350
Have seen some nice dash pad rebuilds. If you’ve done upholstery work should be not too difficult for you.
Common theme is the nicest looking ones were topped with a stretch fabric.
 

midwest

Full Access Member
Joined
Dec 28, 2021
Posts
188
Reaction score
203
Location
Indiana
First Name
Scott
Truck Year
1986
Truck Model
K20
Engine Size
350
This is a long video but this guy is a true pro and makes an art look easy. I thought if I could get mine to look 40% as good as his I would be happy. Couldn't get close so I bought an aftermarket replacement.

xc_hide_links_from_guests_guests_error_hide_media
 

Chris64

Full Access Member
Joined
Sep 16, 2024
Posts
80
Reaction score
110
Location
San Diego
First Name
Chris
Truck Year
1974
Truck Model
K20
Engine Size
350
Have seen some nice dash pad rebuilds. If you’ve done upholstery work should be not too difficult for you.
Common theme is the nicest looking ones were topped with a stretch fabric.
This is more complicated than anything I've done but I figure what's the risk. Vinyl stretches pretty good with a heat gun. Hopefully the glue holds it ok.
 

Chris64

Full Access Member
Joined
Sep 16, 2024
Posts
80
Reaction score
110
Location
San Diego
First Name
Chris
Truck Year
1974
Truck Model
K20
Engine Size
350
Productive day.

Stripping off the original dash is not fun. Heat is your friend.
You must be registered for see images attach


Managed to get it down to mostly shiny metal...except for the rusty bits. I was checking to see if it still fit OK with me prying at it for hours. It's strange to see how wrinkly the original stamped part is. Clearly not the same effort they put into body panels.
You must be registered for see images attach


Finally coated it with some rust reformer. The ends were really rusty and I went about as far as I could with a wire wheel and steel wool. I'm not sure how well this stuff really works but I know I'll be keeping it dry going forward so I think it should be OK.
You must be registered for see images attach


I plan to coat it with some EVA foam tomorrow and hopefully sculpt it mostly back to a stock-ish shape and then fighting vinyl cloth.

If that doesn't work, maybe I'll make a metal dash because it looked pretty cool ;)
 

mano

Junior Member
Joined
Dec 12, 2022
Posts
11
Reaction score
63
Location
Florida
First Name
mano
Truck Year
1979
Truck Model
k10
Engine Size
350
Was thinking of redoing mine myself, but decided to go with this one. Took a couple of hours and putting it in and out half a dozen times had to trim the edges along the windshield and on the sides to get it to fit right. But I’m very happy with it so far.
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
 

Chris64

Full Access Member
Joined
Sep 16, 2024
Posts
80
Reaction score
110
Location
San Diego
First Name
Chris
Truck Year
1974
Truck Model
K20
Engine Size
350
I may go that route. We'll see. Contact cement is slowing down my progress greatly.

Here's the first layer of EVA foam to level out everything. It's dense 3mm foam that I had floating around which was the perfect height. On top of that will be foam made from Harbor Freight floor tiles. They shape easily but smell like a mix of diesel, chemicals & China. So I'm letting them air out for a couple days. Also I learned that the Home Depot non-flammable contact cement is trash so I'm waiting for the good old-fashioned flammable stuff.
You must be registered for see images attach
 

BigT

Full Access Member
Joined
Oct 17, 2024
Posts
70
Reaction score
145
Location
Selah, WA
First Name
Tim
Truck Year
1978
Truck Model
Scottsdale K20
Engine Size
350
Was thinking of redoing mine myself, but decided to go with this one. Took a couple of hours and putting it in and out half a dozen times had to trim the edges along the windshield and on the sides to get it to fit right. But I’m very happy with it so far.
You must be registered for see images attach

Really dig the rattlesnake insert!! Did you do that yourself?
 

fatblazer1973

Junior Member
Joined
Nov 27, 2024
Posts
9
Reaction score
10
Location
North Carolina
First Name
Evan
Truck Year
1973
Truck Model
K5 Blazer
Engine Size
350
This is awesome. I wish you was around when I did mine. I am happy with mine from USA1 Industries it fit great. I did jegs and it fit like garbage!!!
This is mine below. I am some happy and its made with the metal insert and solid. They also said they make it in the US which is awesome.
This is a video highlighting the one they have. I'd say check them out if your in the market for a chevy truck dash pad
xc_hide_links_from_guests_guests_error_hide_media
 

mano

Junior Member
Joined
Dec 12, 2022
Posts
11
Reaction score
63
Location
Florida
First Name
mano
Truck Year
1979
Truck Model
k10
Engine Size
350
Did the shifter too, I need to shoot another one to do some on the door panels
 

Attachments

  • IMG_2797.jpeg
    IMG_2797.jpeg
    143.9 KB · Views: 20
  • IMG_2612.jpeg
    IMG_2612.jpeg
    208.8 KB · Views: 22

tycharles

Junior Member
Joined
Jan 17, 2024
Posts
2
Reaction score
5
Location
Tennessee
First Name
Ty
Truck Year
1985
Truck Model
c10
Engine Size
305
I filled all the speaker holes (and cracks) with fiberglass/bondo and wrapped in leather. btw I like the seam to just be around the gauge bezel not all the way across like some do. just my 2 cents
You must be registered for see images attach
You must be registered for see images attach
 
Last edited:

donnieray

Talks to dogs and trucks.
Joined
Oct 23, 2014
Posts
624
Reaction score
520
Location
Roanoke Rapids NC
First Name
Donnie
Truck Year
84,85,86.
Truck Model
86 C10, 84 K10 MM7 NP833 option truck, 85 K10.
Engine Size
350,355;350.
I filled all the speaker holes (and cracks) with fiberglass/bondo and wrapped in leather. btw I like the seam to just be around the gauge bezel not all the way across like some do. just my 2 cents
You must be registered for see images attach
You must be registered for see images attach
That looks awesome! Congrats.
 

mtbadbob

Full Access Member
Joined
May 9, 2021
Posts
668
Reaction score
1,048
Location
Montana
First Name
Bob
Truck Year
1987
Truck Model
V20
Engine Size
350
Was thinking of redoing mine myself, but decided to go with this one. Took a couple of hours and putting it in and out half a dozen times had to trim the edges along the windshield and on the sides to get it to fit right. But I’m very happy with it so far.
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
LOVE the rattlesnake skin insert!
 

Latest posts

Forum statistics

Threads
44,424
Posts
957,542
Members
36,776
Latest member
Love Samantha
Top