Best way to transport 19 55 gallon barrels?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

R

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,456
Reaction score
8,713
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
The drums are 24 inch diameter. The plot thickens a little, I looked at my square bed and measured it,not sure what bed you are using. You will need 48 inches between the wheel wells and at least 9 foot of length that would have end barrels hanging over 1ft you could gain some length by putting down a piece of plywood 1st, but if you only have 4.5 foot of bed to work with I think you are going to have to remove the tool box.learn to tie a hay hauler hitch so you can lash off a bunch of times,and those tie offs are crazy tight,like compound bow string tight.
 
AuroraGirl

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,693
Reaction score
6,869
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
Ricko1966 said:
The drums are 24 inch diameter. The plot thickens a little, I looked at my square bed and measured it,not sure what bed you are using. You will need 48 inches between the wheel wells and at least 9 foot of length that would have end barrels hanging over 1ft you could gain some length by putting down a piece of plywood 1st, but if you only have 4.5 foot of bed to work with I think you are going to have to remove the tool box.learn to tie a hay hauler hitch so you can lash off a bunch of times,and those tie offs are crazy tight,like compound bow string tight.
Click to expand...
Damnit
can you crunch the math on if i use my gmt800 which is the 6.5 tailgate down with toolbox, and then my trailer which is 10 ft tailgate down, but can only stack 1 high on top of the vertical in the very front (because of the tapered part)

I suppose it would probably only fit 1 high laying down in the entire trailer, right? If so.. maybe thats my play, so I can have those secured by being out of the elements and enclosed, and the ones on the truck wont be so ... tall
 
AuroraGirl

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,693
Reaction score
6,869
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
You must be registered for see images attach
 
R

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,456
Reaction score
8,713
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
I'll do the math in a minute got you a link to a hay hauler hitch, I don't tie it off the same I pull the tail back to a secure point and tie the tail to some thing to maintain tension.But you'll get the idea. Check back I'll put up some pics I shot for a buddy once to tech him when I find them . Here's the video link. I'll crunch your math brb.https://youtube.com/shorts/zvUB6AGWHQ0?feature=shared
 

Attachments

  • 20231106_114249.jpg
    20231106_114249.jpg
    160.9 KB · Views: 34
  • 20231106_114243.jpg
    20231106_114243.jpg
    153.4 KB · Views: 20
  • 20231106_114235.jpg
    20231106_114235.jpg
    193 KB · Views: 22
  • 20231106_114214.jpg
    20231106_114214.jpg
    175.1 KB · Views: 24
AuroraGirl

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,693
Reaction score
6,869
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
Ricko1966 said:
I'll do the math in a minute got you a link to a hay hauler hitch, I don't tie it off the same I pull the tail back to a secure point and tie the tail to some thing to maintain tension.But you'll get the idea. Check back I'll put up some pics I shot for a buddy once to tech him when I find them . Here's the video link. I'll crunch your math brb.https://youtube.com/shorts/zvUB6AGWHQ0?feature=shared
Click to expand...
I should install a stake pocket thing unless the front stake pockets have a opening like the rears do
 
R

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,456
Reaction score
8,713
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
You can do 4 standing up with three on top in the truck that's 4 bottom upright 2 sideways on top 1 on top of that 2 upright on top of the tool box. That's 9. 10 standing up in the trailer that's 19. I'll get the spice bottles back out,pics soon.
 

Attachments

  • 20240923_194715.jpg
    20240923_194715.jpg
    59.3 KB · Views: 17
  • 20240923_194718.jpg
    20240923_194718.jpg
    62.2 KB · Views: 15
  • 20240923_194722.jpg
    20240923_194722.jpg
    52.5 KB · Views: 16
Grit dog

Grit dog

Full Access Member
Joined
May 18, 2020
Posts
6,979
Reaction score
12,231
Location
Auburn, Washington
First Name
Todd
Truck Year
1986, 1977
Truck Model
K20, C10
Engine Size
454, 350
You have a car hauler with a full deck, why not just take that? No need to remove tool boxes, camper shells, etc.
No matter what you do they’ll have to be tied down well. Make 2 rows stacked transverse on the flatbed. Like firewood. Could strap the whole load with 2 straps theoretically.
And zero barrels need to ride in the truck bed or shotgun in the cab.
 
AuroraGirl

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,693
Reaction score
6,869
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
Grit dog said:
You have a car hauler with a full deck, why not just take that? No need to remove tool boxes, camper shells, etc.
No matter what you do they’ll have to be tied down well. Make 2 rows stacked transverse on the flatbed. Like firewood. Could strap the whole load with 2 straps theoretically.
And zero barrels need to ride in the truck bed or shotgun in the cab.
Click to expand...
I am not opposed to it, I was just worried if that was going to be some special consideration for securing the load

And that trailer has like 2 bags of mulch on it, so not at all hard to get ready. To stack them like firewood, youre saying to make little hills out of of them in 2 columns the length of the trailer, then use single straps up and over to hold down?
 
AuroraGirl

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,693
Reaction score
6,869
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
You must be registered for see images attach
You must be registered for see images attach

not sure how this woiuld help but putting it out there
 
bucket

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
30,446
Reaction score
28,356
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
AuroraGirl said:
No, i need trash cans. (I think i will be more organized if i have a trash can nearby more often) and I also need more places for motor oil. Im at 100 gallons and I have bought a few drain pans to avoid dumping them out, i nee capacity. And no im not recylcling

I paid less than 10$
Click to expand...


Are you sure those are 55 gal? It looks like they might be the smaller, 30 gal units?

They do make great trash cans. I cut the tops off, but around the inside of the top flange, so it leaves some beef up there. Then I cut a couple hand holes, about 6" down from the top. To make the hand holes, I use a hole saw and connect them with a little buzz saw which makes a nice oval slot.

I brought home 10 or 12 of the 30 gal drums to use as trash cans. The price was $0 :)
 
Radiohead

Radiohead

That guy on the Columbia
Joined
Mar 17, 2022
Posts
2,486
Reaction score
8,112
Location
Low Earth Orbit where it's safer
First Name
Eric
Truck Year
MCMLXXIX
Truck Model
C-20 Silverado Camper Special
Engine Size
454 crazy cubes, or 7.4 luscious litres
Go to the restaurant supply store and get a roll of that 4mil or thicker clear wrap that is like 2' wide. Set barrels on flatbed, wrap up and strap down. Could sandwich with plywood....

just thinking aloud.
 
mxer147

mxer147

83 K20, 350 vortec, 465, 208, 14/10, 4.10, 33s
Joined
Feb 8, 2023
Posts
608
Reaction score
2,195
Location
Colorado
First Name
Jack
Truck Year
1983
Truck Model
k20
Engine Size
350
Ask a friend or family to come along to drive another truck to help with the transport. Stop someplace nice to share a meal and reminisce about the fall colors, crisp cool air and perhaps share your highlights of the summer.
 
AuroraGirl

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,693
Reaction score
6,869
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
bucket said:
Are you sure those are 55 gal? It looks like they might be the smaller, 30 gal units?

They do make great trash cans. I cut the tops off, but around the inside of the top flange, so it leaves some beef up there. Then I cut a couple hand holes, about 6" down from the top. To make the hand holes, I use a hole saw and connect them with a little buzz saw which makes a nice oval slot.

I brought home 10 or 12 of the 30 gal drums to use as trash cans. The price was $0 :)
Click to expand...
they may be, if so that helps my visual representation, i guess i havent been near them and my only reference is a full 55gallon steel drum from memory
 
AuroraGirl

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,693
Reaction score
6,869
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
bucket said:
Are you sure those are 55 gal? It looks like they might be the smaller, 30 gal units?

They do make great trash cans. I cut the tops off, but around the inside of the top flange, so it leaves some beef up there. Then I cut a couple hand holes, about 6" down from the top. To make the hand holes, I use a hole saw and connect them with a little buzz saw which makes a nice oval slot.

I brought home 10 or 12 of the 30 gal drums to use as trash cans. The price was $0 :)
Click to expand...
I see we have similar ideas on the matter. I have like ... 3? 1 black, 2 blue that are already cut (cut where they are not cicular like waterpirate said
waterpirate said:
no advice on stacking or transport. However Capt. obvious says if using the plastic barrels for garbage you need to cut the top off inside the the rigid ring. if not they deform and flop all over the place. Ask me how I know? lol I cut my first batch the wrong way.
Eric
Click to expand...
They kinda make a more oval opening like that, but one is better than the other 2. I have 2 carboard barrels which are nice for trash too, they lift easier and all that, but i dont want to throw anything with liquids away in them better for my swept up trash / floor dry type deal, packages, paper, cardboard
 
AuroraGirl

AuroraGirl

Full Access Member
Joined
Sep 8, 2019
Posts
9,693
Reaction score
6,869
Location
Northern Wisconsin
First Name
Taylor
Truck Year
1978, 1980
Truck Model
K10, K25
Engine Size
400(?), 350
mxer147 said:
Ask a friend or family to come along to drive another truck to help with the transport. Stop someplace nice to share a meal and reminisce about the fall colors, crisp cool air and perhaps share your highlights of the summer.O
Click to expand...

only person I got who could do that is my dad but he works at that time, not a big deal tho.
 
You must log in or register to reply here.

Similar threads

Nasty-LSX
Best way to run power from truck battery to trailer winch. Quick disconnect ends.
2
Replies
29
Views
2K
Keith Seymore
Keith Seymore
mjck5
gas tank wont fill all the way
Replies
5
Views
246
WFO
WFO
Chris64
Surface rust. What are the best practices?
Replies
11
Views
1K
Grit dog
Grit dog
W
Used a drill to check speedometer forgot I had drill on two and the speedometer spun all the way around
Replies
3
Views
389
Radiohead
Radiohead
T
To remove or not to paint frame?
2
Replies
15
Views
818
Fat 454
Fat 454

Latest posts

Forum statistics

Threads
44,175
Posts
950,912
Members
36,293
Latest member
03z71lt
Top