Where is this interior leak coming from?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

C10SLEY

Member
Joined
Nov 24, 2021
Posts
33
Reaction score
7
Location
Chesnee, SC
First Name
Caleb
Truck Year
1983
Truck Model
C10
Engine Size
383 stroker
When it rains, passenger side gets wet down in the corner angle where your right foot would be. Looks like it’s coming from around the heater core on the right side. Any ideas where it’s coming in from on the outside without me tearing everything apart first?

Thanks!
 

Attachments

  • 03B347D8-F2A6-4C98-8D51-1B7094E9A29E.jpeg
    03B347D8-F2A6-4C98-8D51-1B7094E9A29E.jpeg
    202.4 KB · Views: 35

ali_c20

Full Access Member
Joined
Sep 20, 2016
Posts
1,230
Reaction score
1,741
Location
Austria
First Name
Alexander
Truck Year
1974, 1979
Truck Model
C20, K5
Engine Size
350, 350
Test it. Pour water over the Windshield, if it stays dry pour water in the cowl. This way you can find where the leak sits.
 

Grit dog

Full Access Member
Joined
May 18, 2020
Posts
6,807
Reaction score
11,867
Location
Auburn, Washington
First Name
Todd
Truck Year
1986, 1977
Truck Model
K20, C10
Engine Size
454, 350
Assuming it’s water and not coolant, my money is on from the seam in the cowl and possibly blocked drain hole in the bottom corner of the cowl.
As said above. When it’s dry, start selectively pouring water to help pin point the leak. Take the valance off the cowl so you can see in there. There’s a transverse seam that I believe tends to be a common leak spot. Or rust through hidden somewhere in the cowl or bottom of windshield frame (under the gasket).
Your truck looks real clean though, so not sure if it has any of the damage I mentioned above. But you didn’t mention how it’s been stored over the years.
 

gmbellew

Full Access Member
Joined
May 27, 2018
Posts
1,202
Reaction score
1,250
Location
Kansas city
First Name
glen
Truck Year
1990
Truck Model
suburban 1500
Engine Size
350
The cowl drains get clogged eventually and water stacks up and comes in the kick panel area. Under the truck behind the front fenders is where they drain. You may have to remove a plastic trim piece and pull some foam out of the way. I've had to clean, flush, clean, flush, etc until I got all the debris out.
 

C10SLEY

Member
Joined
Nov 24, 2021
Posts
33
Reaction score
7
Location
Chesnee, SC
First Name
Caleb
Truck Year
1983
Truck Model
C10
Engine Size
383 stroker
Thanks for the recs! The truck sat outside, but not under trees, but near them, for 7 years. Since I’ve had it, it’s been in the dry until now. It’s a pretty clean truck with minimal rust (rockers), but I’m believing y’all that it’s a clogged drain and coming in the kick panel area. The vent in the kick panel was caulked around the perimeter before I pulled it out and restored all my trim pieces. I’ve wonder if it was coming from that vent ever since, but the insulation around the heater core under the dash is very wet…. I’ll be checking this tomorrow hopefully. Been sick, so haven’t addressed it yet.
 

Steelbuddha

Junior Member
Joined
Mar 16, 2024
Posts
13
Reaction score
13
Location
Central North Carolina
First Name
Jonathan
Truck Year
1984
Truck Model
K20 (dump bed)
Engine Size
350
Good to know about the cowl drain holes. I have similar leaks on both sides, despite a new windshield gasket.
 

CountKrunk

Full Access Member
Joined
Aug 3, 2023
Posts
398
Reaction score
913
Location
SW VA
First Name
Count
Truck Year
1984
Truck Model
C20 Custom Deluxe 3+3
Engine Size
v8 350
My truck gets water in through the doors as well with a good rain. The seals are poopy.

Doors will be a whole project themselves someday haha.
 

MikeB

Full Access Member
Joined
Apr 4, 2014
Posts
1,768
Reaction score
991
Location
North Texas
First Name
Mike
Truck Year
1969
Truck Model
C10
Engine Size
355
On my 82, seam sealer under the cowling was not applied very well at the factory, so it eventually cracked and leaked. In may case, water ran down the drivers side and rusted out part of the fuse panel on its way down to rusting out part of the side panel below the fresh air vent. It's worth a look.
 

Attachments

  • IMG-3450.JPG
    IMG-3450.JPG
    251.2 KB · Views: 19

C10SLEY

Member
Joined
Nov 24, 2021
Posts
33
Reaction score
7
Location
Chesnee, SC
First Name
Caleb
Truck Year
1983
Truck Model
C10
Engine Size
383 stroker
On my 82, seam sealer under the cowling was not applied very well at the factory, so it eventually cracked and leaked. In may case, water ran down the drivers side and rusted out part of the fuse panel on its way down to rusting out part of the side panel below the fresh air vent. It's worth a look.
This is kinda what happened... the vent is sealed around the kick panel from the factory, and when I removed the passenger side kick panel when I was restoring all the plastics, I noticed silicone caulk around it, but never replaced it. The truck always sat in the dry then, so I never noticed a leak when I was done restoring the pieces. Well, since it sits outside now, I did.
I found the leak to be from the vent from the water that runs down the cowl and down the side and drips and hits the vent window on the kick panel and drains in. I added a ton of Lexel to both the kick panel and the sheet metal on the cab and put them back together. Putting them back together is a PITA, so I hope I got a good seal. Gave er a quick wash after with no leaks, so now that it's all dry, I need to dump a ton of water down the cowl and see what happens.
 

C10SLEY

Member
Joined
Nov 24, 2021
Posts
33
Reaction score
7
Location
Chesnee, SC
First Name
Caleb
Truck Year
1983
Truck Model
C10
Engine Size
383 stroker
Screen shot from the video I took
 

Attachments

  • IMG_0809.jpeg
    IMG_0809.jpeg
    73.7 KB · Views: 5

Forum statistics

Threads
43,798
Posts
943,444
Members
35,785
Latest member
echo 53
Top