What have you done to your square lately??

[idahovette]

Where to start?
Replaced both tanks, cleaned the lines, rebuilt the carb, fixed a fusible link, troubleshooted the electrical system, cleaned the fuel pump, fused the lines again, resealed the AC compressor, fixed a couple tires, rebuilt the front end, sprayed the underbody with paint, installed a large 2 micron fuel filter, and fired it up! Got it running after at least 8 years.

Wow, what do you do in your spare time?.........lol

 

[Ricko1966]

Where to start?
Replaced both tanks, cleaned the lines, rebuilt the carb, fixed a fusible link, troubleshooted the electrical system, cleaned the fuel pump, fused the lines again, resealed the AC compressor, fixed a couple tires, rebuilt the front end, sprayed the underbody with paint, installed a large 2 micron fuel filter, and fired it up! Got it running after at least 8 years.

So what did you do after lunch? Dang it didn't read Idahovette s post,he beat me. Grrrrr

 

[86burban]

I did an MTV Pimp My Ride customization to my 1984 C30.

 

[hoagster]

@Powerhouse Ranch If you haven't found a lower hose yet I ended up using a Gates 21849. 1.75" at both ends and clears the belts and frame nicely

You must be registered for see images attach

What size oem rubber did you order, I have new ones but they are to small width wise top and bottom. The part number I have is 32-0970, I could just shae them down. My other issue is the nut certs for the A/C condensor!

 

[CalSgt]

What size oem rubber did you order, I have new ones but they are to small width wise top and bottom. The part number I have is 32-0970, I could just shae them down. My other issue is the nut certs for the A/C condensor!

What exactly do you need Mike, I'm not sure I understand your question.

 

[hoagster]

What exactly do you need Mike, I'm not sure I understand your question.

radiator support bushings, do you remember what size you used?

 

[CalSgt]

radiator support bushings, do you remember what size you used?

Sorry Mike, I dug through a box of old used ones and still had to trim them to fit better. I also had an old piece of rubber weather-strip from something I used to support the entire length along the bottom of the radiator since the instructions said to.

 

[CalSgt]

What size oem rubber did you order, I have new ones but they are to small width wise top and bottom. The part number I have is 32-0970, I could just shae them down. My other issue is the nut certs for the A/C condensor!

Also for the rubber condenser nutserts I want to say they clear once they are tightened down. I may have trimmed the bolt a little after they were tightened down too but cant remember. I can take another look next weekend for you.

You must be registered for see images attach

 

[hoagster]

Also for the rubber condenser nutserts I want to say they clear once they are tightened down. I may have trimmed the bolt a little after they were tightened down too but cant remember. I can take another look next weekend for you.

You must be registered for see images attach

Thank you, Yea I have a couple of hurdles like the nutcerts you mentioned.

 

[ChuckN]

Got the plug wires in, new plugs, new header gaskets, just need to re-clock the Edelbrock fuel pump for the fuel line and finish putting in the custom 0/1ga battery cables. Then it’s time for fire up.

You must be registered for see images attach

 

[Goldie Driver]

Had to reach behind the dash to wiggle the bulb holder for the 1st time since March.



Dammit- hope this is a weather fluke and not a sign that more work is needed.

 

[AyWoSch Motors]

Got the new 427 all stripped down and in the shop. Going in the C30 hopefully soonish. What a beast of an engine.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

Also got the core support, fenders, inner fenders, and hood on the k20 before i quit, but its too dark for a good pic. Only held on by about 8 bolts, but its on. More to come tomorrow.

You must be registered for see images attach

 

[drewd]

new seats, new retro sound radio whit 4 new Kicker/Fosgate speakers and Brother 6x9 rear bracket and under seat Sub!

@TPISly-C10 curious how you like this set up after a few years? I was thinking of something very similar

 

[Strick]

Like I had nothing else to do...I took on a new project. I have been wanting another "run around truck". This thing is going to use up some parts that are just sitting around.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[TotalyHucked]

Like I had nothing else to do...I took on a new project. I have been wanting another "run around truck". This thing is going to use up some parts that are just sitting around.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

I've got the bug for another one, been scouring marketplace the last few days haha. Want something to just beat around in that'll haul more than my C10 will