What have you done to your square lately??

[TubeTruck]

pulled the front cover on the 60 to do a little inspection and put in some fresh oil, while it was draining I found a wire retainer off the back of a seal in the bottom of the diff and found there's just a touch of play in the pinion bearing so i'm assuming that's where it came from. Also looking like limited slip, locker or spool time will be coming!

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

ARB Air locker!

 

[86suburban]

I finally started driving mine last week after a year or so of doing way more than I planned to it. I washed it, and installed this crazy expensive cup holder.

You must be registered for see images attach

You must be registered for see images attach

 

[82sbshortbed]

I finally started driving mine last week after a year or so of doing way more than I planned to it. I washed it, and installed this crazy expensive cup holder.

You must be registered for see images attach

You must be registered for see images attach

I like the red and white! Looks good

 

[82sbshortbed]

Got the po drivers side wiper arm and new blade on for inspection.

You must be registered for see images attach

I have 2 new arms with blades but, the old wiper knobs on the assembly are stripped of its teeth. Hence the screw in it to hold it on. I have new assembly too. Just wanna get it on the road as fast as I can.

 

[jjester6000]

I just pulled the head off my engine, and I seem to have a slightly burnt valve.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

Luckily, I have a whole new higher compression head (from a 194 i6) to swap on.

You must be registered for see images attach

You must be registered for see images attach

 

[K201979]

Added a light up bow tie. Needed a new one, figured why not a modern one?

You must be registered for see images attach

I made myself one, and i like it, but had i seen this first i mighta went that route.

You must be registered for see images attach

You must be registered for see images attach

 

[82sbshortbed]

Cleaned up the air horn wiring under the hood.

You must be registered for see images attach

You must be registered for see images attach

 

[Dutch Rutter]

Put my summer boots on, they look small for the truck to me. Really need to wear through these quickly, as well as the MT winter set so I can justify new tires.

You must be registered for see images attach

 

[Mr Clean]

Started taking the front end apart on my 82 Blazer to powder coat the spindels, and backing plates. Also cleaning up the frame preping it for painting.

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[Mr Clean]

Got to put my rear disc brake convertion on the Extracab, and put my new to me shoes on....

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[78C10BigTen]

Got my air horn installed under the hood and working. Just need to tidy up wires and screw the button to the dash. I decided just to buy a button rather trying to chase horn wire. Kinda proud I figured out the wiring because I'm not too familiar with relays. One step closer to getting my safety inspection and get plates and tags.

You must be registered for see images attach

What does that sound like?

 

[78C10BigTen]

I'm glad I'm not the only one that chooses not to deal with removing the extra crossmember bolts.

I took those upper supports off while doing trans swaps and also never put them back on! Lol that makes 3 of us

 

[Poppy 87]

Got to put my rear disc brake convertion on the Extracab, and put my new to me shoes on....

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

What calipers are you using for the rear conversion?

Sent from my XT1254 using Tapatalk

 

[78C10BigTen]

Well this was actually last weekend but i been havin phone issues so i never got it posted. Started out by noticing no fuel in my filter with the truck runnin so i bought another fuel pump. I added a pressure gauge in line with my old pump and holy cow was it wildly erratic! So i commenced to putting on a new pump and inspecting the push rod. I messed up the plate gasket and didnt have another so i improvised! Got everythin all back together and it runs 9psi but still no fuel in the filter and seems to not pump it up there. Im lost because i drive it daily this way with no issue, hows that possible?!

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

You must be registered for see images attach

 

[78C10BigTen]

Few more plus the video of the gauge.

xc_hide_links_from_guests_guests_error_hide_media

You must be registered for see images attach