Opinions please on possible use for zinc oil additive

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

mtnmankev

Full Access Member
Joined
Jun 10, 2014
Posts
1,623
Reaction score
3,293
Location
Ash Fork, Arizona
First Name
Kevin
Truck Year
1984, 1983
Truck Model
K10, C20
Engine Size
383 Stroker, 350
Not sure where to post this, so I put it here, feel free to move the thread if needed.
Weather here has been brutally cold, so much that I rely on the remote electric start on my generator as I can't hobble out in the cold and snow to start it.
The unit is only 3 years old, and doesn't have a ton of hours on it, and runs rather good.
This morning when I got up at 3AM to relight the woodstove, and fire up the propane Mr Heater rocket to warm the house up quickly, I heard a KNOCK,KNOCK,KNOCK from the generator shed, then it started up and ran normal.
Experience has taught me that when a small engine develops a rod knock it's about ready to blow up, and I'm sure the cold thick oil didn't help matters any.
Anyway, I am now forced to spend a thousand bucks on a new generator, and want to avoid this situation again, and was thinking of adding some zinc oil additive every oil change.
Opinions please if anybody thinks it will help or not ??
I wish there was a way to have a warm enclosed building so the poor thing never gets all that cold, but ventilation for exhaust and fresh air intake would be issues hard to overcome, the generator shed has 3 walls and no door, so that one large opening has provided adequate airflow up to now.
Have I ever mentioned how much winter sucks and I hate snow and single digit temperatures ??
 

CalSgt

Full Access Member
Joined
Oct 3, 2021
Posts
1,700
Reaction score
3,762
Location
CA
First Name
Casey
Truck Year
1980
Truck Model
Chevy K-10 Custom Deluxe
Engine Size
350
Probably wouldn't hurt to use a zinc additive... I would just use an oil that has a decent zinc content without the need for an additive. Any oil marketed for "Classic cars" or maybe "High Mileage" probably contains more zinc.

Most new cars don't need the zinc so oil manufacturers stopped using it in their most common engine oils. One of the biggest causes for oil to have zinc is flat tappet camshafts, GM started using roller cams in nearly everything including pick-up trucks by 1996.
 

mtnmankev

Full Access Member
Joined
Jun 10, 2014
Posts
1,623
Reaction score
3,293
Location
Ash Fork, Arizona
First Name
Kevin
Truck Year
1984, 1983
Truck Model
K10, C20
Engine Size
383 Stroker, 350
I have been using Castrol GTX 10W30 in all my 4 stroke engines for many decades, never had an issue from the oil.
I see it's available in a high zinc version for classic cars, but only in 20W50 which is too thick especially when it's cold like it's been.
 

mtnmankev

Full Access Member
Joined
Jun 10, 2014
Posts
1,623
Reaction score
3,293
Location
Ash Fork, Arizona
First Name
Kevin
Truck Year
1984, 1983
Truck Model
K10, C20
Engine Size
383 Stroker, 350
At 610 ppm, I might think that could be sufficient for the GTX.
It's definitely higher than zero, and easy to find 10w30 on the shelf.
I started the generator a couple minutes ago, and maybe the daytime warming made a difference, but no knocking sounds and it fired up immediately.
 

Camar068

Supporting Member
Supporting Member
Joined
Feb 5, 2014
Posts
4,293
Reaction score
3,339
Location
Kentucky
First Name
David
Truck Year
1986
Truck Model
K10/LM7 5.3/4L60e/np208/3.73/32"
Engine Size
10 yrs Air Force
Below is an excellent site to check and/or compare oils, contents and such. Type in the search bar down a bit and on the right.

PETROLEUM QUALITY INSTITUTE OF AMERICA


Some will even give you a more in depth analysis of the oil such as the link below. The link after that is one that doesn't give you all that info for that specific brand (same website). So if you want to compare Amazon oil to lets say Amsoil, right click on the first one you look up....and open in NEW WINDOW....minimize that window and select the other oil in the other window. resize each window so you can put them side by side on your computer screen and compare.

Amazon Oil

Speedway
 
Last edited:

Shorty81

Baby Boomer
Joined
Mar 19, 2018
Posts
3,101
Reaction score
5,778
Location
North West ohio
First Name
Darren
Truck Year
86
Truck Model
K20
Engine Size
496
I use Schaeffer oil, contains Zinc.
 

Attachments

  • schaeffer-709-racing-oil-gallon-6.jpeg
    schaeffer-709-racing-oil-gallon-6.jpeg
    113.3 KB · Views: 62

Grit dog

Full Access Member
Joined
May 18, 2020
Posts
6,970
Reaction score
12,220
Location
Auburn, Washington
First Name
Todd
Truck Year
1986, 1977
Truck Model
K20, C10
Engine Size
454, 350
At 610 ppm, I might think that could be sufficient for the GTX.
It's definitely higher than zero, and easy to find 10w30 on the shelf.
I started the generator a couple minutes ago, and maybe the daytime warming made a difference, but no knocking sounds and it fired up immediately.
Engine knocks that go away are generally never rod or wrist pin knocking. IE not about to blow up.
I also wouldn’t even spend any $ on zinc. But a quality year round synthetic oil like Rotella T6 5-40 is a good idea.
 

mtnmankev

Full Access Member
Joined
Jun 10, 2014
Posts
1,623
Reaction score
3,293
Location
Ash Fork, Arizona
First Name
Kevin
Truck Year
1984, 1983
Truck Model
K10, C20
Engine Size
383 Stroker, 350
Engine knocks that go away are generally never rod or wrist pin knocking. IE not about to blow up.
I also wouldn’t even spend any $ on zinc. But a quality year round synthetic oil like Rotella T6 5-40 is a good idea.
I can go along with that in an engine that doesn't have oil pressure delivered by a pump.
Have seen many automotive engines with worn rod bearings that quit knocking as soon as oil pressure builds.
Of course, when they wear past a certain point, they are going to tap or knock all the time, even with pressure.
 

Big Ray

Full Access Member
Joined
Oct 14, 2022
Posts
1,243
Reaction score
4,255
Location
North Carolina
First Name
Ray
Truck Year
1979
Truck Model
K5
Engine Size
400
Sounds like you have the wrong oil in it.
Change it to one with proper temp range for your location.
Just my .02...
 

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,446
Reaction score
8,684
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
I was going to say Rotella t4 oil still has zinc and what I use in my flat tappet engines. I was told thats what to run by whatever big conglomerate owns half the oil companies in the U.S. The reason I worded it that way was I think it was valvoline I called to get a recommendation as to which of their racing oils to run in my Chevelle. Their tech guy told me which all companies in their group were the same with different labels,he said Rotella t4 disregard that it says diesel it's B.S. wording so people don't trash the converters in their gasoline cars.
Was going to say it's main purpose is to give pressure resistance to the oil to keep the cams from going flat. But as I thought about it small engines are splash oiled having zinc in the oil so it stays where it belongs is probably a good idea.
 
Last edited:

Matt69olds

Full Access Member
Joined
Jan 8, 2018
Posts
2,451
Reaction score
3,819
Location
Central Indiana
First Name
Matt
Truck Year
81
Truck Model
GMC 1/2 ton
Engine Size
455 Olds
I would think any engine made in the last 15 years would be fine on low zinc oil. I would especially think a generator engine would be perfectly content on just about any quality oil of the proper weight. Those aren’t high rpm engines, they basically run at the same speed. I bet the valve springs are pretty lightweight.

If you’re really concerned, cut open the oil filter. If something is starting to wear or is damaged, you will find the shrapnel there.

If the filter is clean, install a new filter, refill it with the proper weight oil for the environment, and relax. You might even consider a synthetic oil, synthetic oils flow better at low temperatures, and deal with heat far better than oil school petroleum based oils.

Do you have any paperwork on the generator? Does it give a recommended oil type for cold weather use? If all else fails, read the instructions!!!
 

mtnmankev

Full Access Member
Joined
Jun 10, 2014
Posts
1,623
Reaction score
3,293
Location
Ash Fork, Arizona
First Name
Kevin
Truck Year
1984, 1983
Truck Model
K10, C20
Engine Size
383 Stroker, 350
The engine is a Honda clone, no filter, Cabelas brand generator, runs at 3600 rpm.
4KW unit.
The paperwork is lost, but all the generators I have had over the years say use a good 10w30 all year round for the average temperatures here.
If I lived somewhere it went below zero, I would run a lighter oil.
It is possible however, that single digit temps are too cold for 10w30, and it sucks that I have to use the generator for power when it's that cold, but this winter has been an exception here, it rarely gets much below the 20's
 

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,446
Reaction score
8,684
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
I wasn't worrying about camshaft wear I was thinking of the benefits of difference in squishing the oil out of the connecting rod big end with zinc. Squishing is not a technical term but I didn't want to use the word pressure because people are going to start saying that engine doesn't have oil pressure. Correct. But zinc is a pressure additive keeps lubrication in place under pressure. Maybe not necessary but I use a zinc oil in everything.
 

Latest posts

Forum statistics

Threads
44,162
Posts
950,639
Members
36,273
Latest member
dannyphx
Top