projectmidnight74
Full Access Member
- Joined
- Jul 10, 2023
- Posts
- 117
- Reaction score
- 65
- Location
- Mississippi
- First Name
- Eddie
- Truck Year
- 1974
- Truck Model
- C10
- Engine Size
- V8
Oil sending unit hole issue
- Thread starter projectmidnight74
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
squaredeal91
Full Access Member
- Joined
- Mar 10, 2023
- Posts
- 2,595
- Reaction score
- 4,730
- Location
- Cave junction Oregon
- First Name
- Greg bush
- Truck Year
- 1991 SB
- Truck Model
- K30
- Engine Size
- 5.9 Cummins 12 valve
Its just a pipe plug.
Did you try a 12 point socket?
Also when you find a close one just tap it on and loosen it up
Did you try a 12 point socket?
Also when you find a close one just tap it on and loosen it up
Old Guy Bill
Full Access Member
- Joined
- Sep 10, 2023
- Posts
- 449
- Reaction score
- 1,380
- Location
- KY
- First Name
- Bill
- Truck Year
- 1978
- Truck Model
- K20
- Engine Size
- 400
There are sockets made for them if you can’t get vise grips on it.
You must be registered for see images attach
- Joined
- Aug 3, 2010
- Posts
- 30,637
- Reaction score
- 28,926
- Location
- Usually not in Ohio
- First Name
- Andy
- Truck Year
- '77, '78, '79, '84, '88
- Truck Model
- K5 thru K30
- Engine Size
- 350-454
Yep, what he said^^^
It's just a square drive pipe plug. It's 1/8" NPT thread. The size of the square drive varies by manufacturer.
WFO
Full Access Member
- Joined
- Jan 6, 2017
- Posts
- 3,717
- Reaction score
- 5,110
- Location
- Texas Panhandle
- First Name
- Dan
- Truck Year
- 1986
- Truck Model
- K20
- Engine Size
- 350
How about using a 3/8" or 1/2" deep socket ,with the square end on the plug, and turn it with a pipe wrench?
idahovette
Full Access Member
- Joined
- Aug 7, 2016
- Posts
- 7,359
- Reaction score
- 16,113
- Location
- Weiser Idaho
- First Name
- Perry
- Truck Year
- 1975-1979
- Truck Model
- K20-K10
- Engine Size
- 350
^^^^^^^or use the right Allen wrench in the end of said socket?^^^^
Grit dog
Full Access Member
- Joined
- May 18, 2020
- Posts
- 7,105
- Reaction score
- 12,513
- Location
- Auburn, Washington
- First Name
- Todd
- Truck Year
- 1986, 1977
- Truck Model
- K20, C10
- Engine Size
- 454, 350
Male Allen socket back to square drive from the socket on the pipe plug is a solid reverse engineer to get it back to something you can us an impact on if it’s stuck stuck.
- Joined
- Aug 3, 2010
- Posts
- 30,637
- Reaction score
- 28,926
- Location
- Usually not in Ohio
- First Name
- Andy
- Truck Year
- '77, '78, '79, '84, '88
- Truck Model
- K5 thru K30
- Engine Size
- 350-454
I forgot to point out, OP did a darn fine job of getting that picture of the pipe plug. That can be a hard area to see.
brooksman9
Full Access Member
- Joined
- Sep 26, 2021
- Posts
- 565
- Reaction score
- 1,629
- Location
- Olive Branch, MS
- First Name
- Patrick
- Truck Year
- 1986
- Truck Model
- Silverado & Custom Deluxe
- Engine Size
- 350 & 305
May need to apply a little heat to that area as well.
plumtruckerd
Junior Member
- Joined
- Jul 30, 2023
- Posts
- 20
- Reaction score
- 33
- Location
- Pittsburgh
- First Name
- Mike
- Truck Year
- 1986
- Truck Model
- C3500
- Engine Size
- 5.7
Use an extension, upside down, and turn the other end with a wrench.
1STLS1
Full Access Member
- Joined
- Dec 9, 2018
- Posts
- 212
- Reaction score
- 539
- Location
- West Phoenix AZ
- First Name
- MIchael
- Truck Year
- 1985
- Truck Model
- K10
- Engine Size
- 350
Is there an easier pipe plug to reach down by the oil filter to tap into the oil gallery? Maybe with a allen head, that you could remove and add a sensor?
Similar threads
