87silveradok20
Full Access Member
- Joined
- Jun 29, 2014
- Posts
- 684
- Reaction score
- 138
- Location
- Ohio
- First Name
- Levi
- Truck Year
- 1987
- Truck Model
- Silverado k20
- Engine Size
- 350
Hopefully this thread can help someone and feel free to ask questions.
Anyways I started out with a 1987 4x4 with the tbi 350 and now I have a 370hp 355 running the Holley sniper. I’m going to attempt to go step by step in what I did in regards to each step of the tbi to sniper conversion.
Fuel system:
I went the cheap route for my fuel system. I put the three port sensing units without the pump in my tanks then ran normal rubber line from my tanks to the switching valve and from the switching valve to the pump. Then I used high pressure rubber line from the pump to factory filter and from the factory filter to the back of the sniper. For the return I cut the threaded end off of the factory line and ran a normal fuel line from the back of the sniper to where I cut the factory line on the fuel rail. Eventually I plan to switch everything to AN braided steel lines.
Mounting:
The Holley sniper bolts right on to a regular 4 barrel carb flange. So to make it bolt up to your factory engine you will need a new intake manifold. I currently am using my factory throttle cable but I feel there is room for improvement with it. It’s working for now tho so I am gonna leave it till I finish up some other projects.
Wiring:
For the Holley sniper to work properly you need 4 wires. I ran the power and ground together over to the battery and hooked them in there. I found ignition power in the old harness and used it to power the sniper on with the key and then you need to get a tach signal from somewhere so I ran that wire to my distributor(a normal vacuum advance distributor). I also went through my entire factory wiring harness and removed any wiring that wasn’t needed. The only wires that I kept were oil psi and temp sending unit wires, the brown wire to the distributor, and two ignition power wires(one for the sniper and one for the distributor).
Other stuff:
I also used the sniper to control my fuel pump, tach, and electric fans. These functions are optional but obviously very convenient. Another point that’s very important to remember is that if you have a th400 trans your lockdown is computer controlled and obviously if you remove the computer it won’t work. I’m working on figuring out if I can use an output of the sniper to control this or not. If I can’t then I’ll
Just put a switch on the gas pedal.
Feel free to ask me any questions you may have or add any experience in from guys who have done something similar. Also let me know what pictures you wanna see.
Sent from my iPhone using Tapatalk
Anyways I started out with a 1987 4x4 with the tbi 350 and now I have a 370hp 355 running the Holley sniper. I’m going to attempt to go step by step in what I did in regards to each step of the tbi to sniper conversion.
Fuel system:
I went the cheap route for my fuel system. I put the three port sensing units without the pump in my tanks then ran normal rubber line from my tanks to the switching valve and from the switching valve to the pump. Then I used high pressure rubber line from the pump to factory filter and from the factory filter to the back of the sniper. For the return I cut the threaded end off of the factory line and ran a normal fuel line from the back of the sniper to where I cut the factory line on the fuel rail. Eventually I plan to switch everything to AN braided steel lines.
Mounting:
The Holley sniper bolts right on to a regular 4 barrel carb flange. So to make it bolt up to your factory engine you will need a new intake manifold. I currently am using my factory throttle cable but I feel there is room for improvement with it. It’s working for now tho so I am gonna leave it till I finish up some other projects.
Wiring:
For the Holley sniper to work properly you need 4 wires. I ran the power and ground together over to the battery and hooked them in there. I found ignition power in the old harness and used it to power the sniper on with the key and then you need to get a tach signal from somewhere so I ran that wire to my distributor(a normal vacuum advance distributor). I also went through my entire factory wiring harness and removed any wiring that wasn’t needed. The only wires that I kept were oil psi and temp sending unit wires, the brown wire to the distributor, and two ignition power wires(one for the sniper and one for the distributor).
Other stuff:
I also used the sniper to control my fuel pump, tach, and electric fans. These functions are optional but obviously very convenient. Another point that’s very important to remember is that if you have a th400 trans your lockdown is computer controlled and obviously if you remove the computer it won’t work. I’m working on figuring out if I can use an output of the sniper to control this or not. If I can’t then I’ll
Just put a switch on the gas pedal.
Feel free to ask me any questions you may have or add any experience in from guys who have done something similar. Also let me know what pictures you wanna see.
Sent from my iPhone using Tapatalk
