Engine lag

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

1974Blueflame

Junior Member
Joined
Oct 10, 2024
Posts
3
Reaction score
1
Location
east bay
First Name
cole
Truck Year
1974
Truck Model
K1500
Engine Size
350 V8
Not sure what’s wrong had to get it towed a while ago motor has a ticking sound and can has unusual shake now at idle and in drive. At idle while pressing throttle it just wants to lose power if anyone has had this problem before or any insight on what might be going wrong.
Timing, Plugs , ?
 

Cousin_Eddie

Junior Member
Joined
Sep 29, 2024
Posts
4
Reaction score
4
Location
South Dakota
First Name
Clyde
Truck Year
1984
Truck Model
C10
Engine Size
350
Maybe a vacuum leak? My sons truck was doing the same thing. Vacuum hose was burned through (laying on the headers) as well as the brake booster rusted clean through on the bottom. Engine would shudder and die sometimes when you stepped on the brakes. Especially at idle.
 

Truck82

Member
Joined
Nov 2, 2024
Posts
62
Reaction score
119
Location
Alderton
First Name
Christopher
Truck Year
1982
Truck Model
c20
Engine Size
350
When I first put my engine together I misplaced a few vacuum lines and had quite a few leaks. My engine was doing exactly what you’re describing… shake, loss of power.
Another possibility for loss of power when you get into the throttle is you could be running a too rich fuel/air mixture. You can tell this by the black-ish color exhaust.
I definitely would check your timing also. That will give it a bad shake if it’s too far out.
I hope this helps some.
Good luck!
 

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,369
Reaction score
8,565
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
Not sure what’s wrong had to get it towed a while ago motor has a ticking sound and can has unusual shake now at idle and in drive. At idle while pressing throttle it just wants to lose power if anyone has had this problem before or any insight on what might be going wrong.
Timing, Plugs , ?
If it developed a tick at the same time, my first suspicion is valve train. Poor man's power balance test take the girdle off the plug wires. Engine running grab a plug wire a couple of inches from the distributor cap,wiggle and pull up until the wire comes off,listen for the idle to change. Repeat until you find cylinders that make no change to idle. Test resistance on those plug wires,examine those plugs,run compression on those cylinders. If you have headers,which I'm assuming you don't. Instead of checking at the distributor you can wet a couple of fingers and just tap the headers by the ports,the cold cylinders are suspect. Both of these methods require a little common sense,so you don't get burned or shocked. You probably will get shocked a couple of times,it really doesn't hurt. Ignore this suggestion if you have a pace maker or medical condition that getting shocked might hurt you.
 

TX87R10

Full Access Member
Joined
Jun 25, 2020
Posts
1,071
Reaction score
2,231
Location
Texas
First Name
Txr10
Truck Year
1987
Truck Model
R10
Engine Size
305
I had a bad alternator that was causing lurching randomly as the power surged. More noticable at night with the lights on.
 

fast 99

Full Access Member
Joined
Dec 31, 2021
Posts
2,003
Reaction score
2,884
Location
Spokane, Washington
First Name
Brian
Truck Year
81,85
Truck Model
K20
Engine Size
350
If it developed a tick at the same time, my first suspicion is valve train. Poor man's power balance test take the girdle off the plug wires. Engine running grab a plug wire a couple of inches from the distributor cap,wiggle and pull up until the wire comes off,listen for the idle to change. Repeat until you find cylinders that make no change to idle. Test resistance on those plug wires,examine those plugs,run compression on those cylinders. If you have headers,which I'm assuming you don't. Instead of checking at the distributor you can wet a couple of fingers and just tap the headers by the ports,the cold cylinders are suspect. Both of these methods require a little common sense,so you don't get burned or shocked. You probably will get shocked a couple of times,it really doesn't hurt. Ignore this suggestion if you have a pace maker or medical condition that getting shocked might hurt you.
Might try disabling spark then cranking over. A cylinder not filling or low compression, starter will increase speed and be uneven on a bad cylinder. I used it many times diagnosing a misfire. Suggested what direction to proceed with diagnosis. If available hook up a vacuum gauge.
 

Forum statistics

Threads
44,064
Posts
948,662
Members
36,130
Latest member
TIOleo520
Top