NOPHO84K30
Full Access Member
- Joined
- Feb 28, 2013
- Posts
- 482
- Reaction score
- 103
- Location
- north phoenix
- First Name
- justin
- Truck Year
- 1984 silverado k30
- Truck Model
- K30 dana 60 corp14 ff
- Engine Size
- 454 sm465 np205
diy4x guardsmen 14 bolt
- Thread starter NOPHO84K30
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
77 K20
Full Access Member
- Joined
- Nov 9, 2012
- Posts
- 3,101
- Reaction score
- 3,119
- Location
- Montana
- First Name
- Mike
- Truck Year
- 1977
- Truck Model
- K20 5" lift
- Engine Size
- HT383 fuel injected
*tracking* I've looked at that as I thought it would offer great protection.
Powder coating would be a good idea. I was thinking it might get packed full of mud and snow a lot and then require me to clean it out a lot. Not sure that would be an issue or not.
Powder coating would be a good idea. I was thinking it might get packed full of mud and snow a lot and then require me to clean it out a lot. Not sure that would be an issue or not.
NOPHO84K30
Full Access Member
- Joined
- Feb 28, 2013
- Posts
- 482
- Reaction score
- 103
- Location
- north phoenix
- First Name
- justin
- Truck Year
- 1984 silverado k30
- Truck Model
- K30 dana 60 corp14 ff
- Engine Size
- 454 sm465 np205
marks86
Full Access Member
- Joined
- Feb 2, 2011
- Posts
- 1,513
- Reaction score
- 90
- Location
- Latham, NY
- First Name
- Mark
- Truck Year
- 1986
- Truck Model
- K30
- Engine Size
- 12v Cummins
I need one of those. nice product
NOPHO84K30
Full Access Member
- Joined
- Feb 28, 2013
- Posts
- 482
- Reaction score
- 103
- Location
- north phoenix
- First Name
- justin
- Truck Year
- 1984 silverado k30
- Truck Model
- K30 dana 60 corp14 ff
- Engine Size
- 454 sm465 np205
Install only took maybe 20mins. Unbolted drive shaft dang cup came off had to put some bearings back in line then taped it up so it wouldn't happen again then the 6 or so bolts around the pinion came out and it slid right over the yoke into place then the grade 8 bolts that came with it went back in...theyre alittle longer then the other ones to make up the thickness of the guard. It was really easy.
Ill let you know next time i go muddin if it scoops up mud. It may act like a slide and go over it ...it is higher then the bottom of the dif to so itll hit dif first or its going to dig in like a shovel. Ill let ya know
Ill let you know next time i go muddin if it scoops up mud. It may act like a slide and go over it ...it is higher then the bottom of the dif to so itll hit dif first or its going to dig in like a shovel. Ill let ya know
firebane
Full Access Member
- Joined
- Jul 10, 2014
- Posts
- 1,732
- Reaction score
- 30
- Location
- Calgary, AB
- First Name
- Curtis
- Truck Year
- 1974
- Truck Model
- K10
- Engine Size
- 350
In any deep water or mud I've heard of these things acting like a shovel and scooping up water/mud/dirt and even people getting stuck because they get stuck against something.
Looks good though.
Looks good though.
