Blue Print or GM Performance
- Thread starter Maknwine
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
Bextreme04
Full Access Member
- Joined
- May 13, 2019
- Posts
- 4,464
- Reaction score
- 5,632
- Location
- Oregon
- First Name
- Eric
- Truck Year
- 1980
- Truck Model
- K25
- Engine Size
- 350-4bbl
Yes, that 30W is what I used in my 350 rebuild. It is about $10 cheaper ordered through Amazon. I also used the 6 quart box of 10w-30 of the same stuff in my Gen VI 454 rebuild. Its good stuff
tadslc
Full Access Member
- Joined
- Jan 20, 2020
- Posts
- 120
- Reaction score
- 134
- Location
- Birmingham, AL
- First Name
- Tad
- Truck Year
- 1981
- Truck Model
- C10
- Engine Size
- 350 Blueprint
Here is what I am going to use- Lucas Oil 10630-6PK SAE 30WT Break-in Oil - 1 Quart, (Case of 6)
Also from AmazonAfter the initial break in I'll be using the Lucas Hot Rod and Classic oil.
Maknwine
Full Access Member
- Joined
- Nov 24, 2016
- Posts
- 101
- Reaction score
- 141
- Location
- Virginia
- First Name
- Tom
- Truck Year
- 1987
- Truck Model
- c30
- Engine Size
- 5.7
Very slow progress....largely its just how I do but also its hot, summer yards duties, it's too freaking hot, and everybody else's problems precede my own. Whiney complaint over.
Got the IM painted/cleared, pulley's p/c also, engine mount brackets done also. Have a list of items on Rock auto in the cart. I'm going all new clutch parts(going to use LUK) even getting a new slave and hydraulic cylinder. The clutch before never really felt right and I'm just going new parts and see what happens. Have the water pump cleaned up and going to put some paint on it also this week. Once I get the new parts(also all new IM bolts), I can put the intake manifold on and other small parts that need thread sealant etc.
Got the IM painted/cleared, pulley's p/c also, engine mount brackets done also. Have a list of items on Rock auto in the cart. I'm going all new clutch parts(going to use LUK) even getting a new slave and hydraulic cylinder. The clutch before never really felt right and I'm just going new parts and see what happens. Have the water pump cleaned up and going to put some paint on it also this week. Once I get the new parts(also all new IM bolts), I can put the intake manifold on and other small parts that need thread sealant etc.
You must be registered for see images attach
tadslc
Full Access Member
- Joined
- Jan 20, 2020
- Posts
- 120
- Reaction score
- 134
- Location
- Birmingham, AL
- First Name
- Tad
- Truck Year
- 1981
- Truck Model
- C10
- Engine Size
- 350 Blueprint
Make sure and get your flywheel resurfaced if you aren't replacing.
Maknwine
Full Access Member
- Joined
- Nov 24, 2016
- Posts
- 101
- Reaction score
- 141
- Location
- Virginia
- First Name
- Tom
- Truck Year
- 1987
- Truck Model
- c30
- Engine Size
- 5.7
Right on @tadslc .... the teeth look to be in great shape and the surface I think shouldn't take much true up. From the few clutch disk I've seen this one has right much life left in it but I'm going new and hope it will be a long time before it ever needs replacing.
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
tadslc
Full Access Member
- Joined
- Jan 20, 2020
- Posts
- 120
- Reaction score
- 134
- Location
- Birmingham, AL
- First Name
- Tad
- Truck Year
- 1981
- Truck Model
- C10
- Engine Size
- 350 Blueprint
That flywheel surface definitely looks like it needs a good surfacing.
But new is good too
But new is good too
Maknwine
Full Access Member
- Joined
- Nov 24, 2016
- Posts
- 101
- Reaction score
- 141
- Location
- Virginia
- First Name
- Tom
- Truck Year
- 1987
- Truck Model
- c30
- Engine Size
- 5.7
Ordered some intake manifold bolts and would like to know If I should be concerned that the new ARP bolts are shorter than the originals. New ones are smaller heads and IMO would need to have the washers which shortens them that much more vs originals.
Is this normal or should I just go buy grade bolts from the hardware store that match better?
Is this normal or should I just go buy grade bolts from the hardware store that match better?
You must be registered for see images attach
Craig Nedrow
NADAR UNDER THE RADAR
- Joined
- Sep 1, 2018
- Posts
- 1,120
- Reaction score
- 2,427
- Location
- Washington State
- First Name
- Craig
- Truck Year
- 1973 (have two), 1985
- Truck Model
- K10, K20, C20
- Engine Size
- 350, 454, 6.2 Detroit
Catbox that sentence caught my eye, made me smile.
Craig Nedrow
NADAR UNDER THE RADAR
- Joined
- Sep 1, 2018
- Posts
- 1,120
- Reaction score
- 2,427
- Location
- Washington State
- First Name
- Craig
- Truck Year
- 1973 (have two), 1985
- Truck Model
- K10, K20, C20
- Engine Size
- 350, 454, 6.2 Detroit
Rule of thumb in the machinist world, would diaXdepth. EX: 5/16 bolt with 5/16 thread engagement, MIN!!!In Aluminum like 6061 add half again as much IE: 1.5 times the dia.
Catbox
Full Access Member
- Joined
- Jul 12, 2018
- Posts
- 4,473
- Reaction score
- 16,801
- Location
- Just Outside of Portland Oregon
- First Name
- Peter
- Truck Year
- 1979
- Truck Model
- C20 Silverado Camper Special
- Engine Size
- 461
Big bugger just turned over 240,000 this week.
You must be registered for see images attach
