Aftermarket hood does not open

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

BunzCarz

Junior Member
Joined
Jul 13, 2024
Posts
9
Reaction score
32
Location
VA
First Name
Michael
Truck Year
1986
Truck Model
2500
Engine Size
5.7
I have a 1986 Cummins swapped Suburban with an aftermarket hood. The hood did not have a spring in front so the PO told me to jamb something between the hood and the grill when pulling the hood release handle. This only worked sometimes and it usually took me a few pulls of the handle to get the hood latch to disengage with the loop on the hood so I could open the hood. I replaced the spring and now I can't open the hood, even with jamming something between the hood and the grill. Has anyone ever run into this? I'm new to squarebodys but I think the position of the loop that engages the hood latch might be part of the issue. The safety latch was removed because the intercooler fills the space that the hook part of the safety latch would usually fit. I currently have a piece of cable connected to the loop on the hood with a carabiner. Any advice on an alternate safety latch?
 

Scott91370

Full Access Member
Joined
Apr 2, 2018
Posts
997
Reaction score
1,019
Location
Burleson, Tx
First Name
Scott
Truck Year
1985
Truck Model
Sierra1500
Engine Size
350
Could be too much pressure. Have someone push down slightly on the hood where the latch is and see if that releases it.
 

TotalyHucked

Full Access Member
Joined
Feb 24, 2020
Posts
3,671
Reaction score
11,854
Location
Auburn, Georgia
First Name
Zach
Truck Year
1985
Truck Model
Sierra 1500
Engine Size
5.3
Got any pictures? That would go a long way in helping us figure it out

Have you tried pushing down on the hood after you've pulled the cable? For my '85, with a new cable and well lubricated latch, I have to whack the hood after I've pulled the release every time.
 

bucket

Super Moderator
Staff member
Super Moderator
Joined
Aug 3, 2010
Posts
30,438
Reaction score
28,342
Location
Usually not in Ohio
First Name
Andy
Truck Year
'77, '78, '79, '84, '88
Truck Model
K5 thru K30
Engine Size
350-454
Could be too much pressure. Have someone push down slightly on the hood where the latch is and see if that releases it.

^^^ This^^^

If a hood latch is out of adjustment, the pressure from the spring can cause the latch to bind more.

When you finally get the hood open, remove the latch. Then adjust the hood to lay closed properly. Then install the latch and adjust it so the hood will close and still line up when it's latched. During the latch adjustment process, DO NOT fully latch the hood if you feel any kind of binding as the hood is pushed down. The goal is to get the side-side latch adjustment done first, so that the hood striker doesn't drag down either side of the latch. Then work on the up-down latch adjustment, so that the hood latches closed fully, without putting too much pressure on the two front hood bumper stops.
 

BunzCarz

Junior Member
Joined
Jul 13, 2024
Posts
9
Reaction score
32
Location
VA
First Name
Michael
Truck Year
1986
Truck Model
2500
Engine Size
5.7
^^^ This^^^

If a hood latch is out of adjustment, the pressure from the spring can cause the latch to bind more.

When you finally get the hood open, remove the latch. Then adjust the hood to lay closed properly. Then install the latch and adjust it so the hood will close and still line up when it's latched. During the latch adjustment process, DO NOT fully latch the hood if you feel any kind of binding as the hood is pushed down. The goal is to get the side-side latch adjustment done first, so that the hood striker doesn't drag down either side of the latch. Then work on the up-down latch adjustment, so that the hood latches closed fully, without putting too much pressure on the two front hood bumper stops.
I got the hood open, then I adjusted the latch. I also lubricated the latch and all the hood hinges. I didn't realize that when you pull the hood release handle the latch only moves part way and when you release the handle the latch opens fully. I think the latch was binding on the second action of the latch when the handle is released inside the cab. So I think a combination of cleaning and lubing the latch and adjusting the position solved the issue. Thanks to everyone for the help. Now I need to figure out how to modify the safety latch since the intercooler blocks the original hole the safety latch fits into.
 

Attachments

  • 20241107_195632[1].jpg
    20241107_195632[1].jpg
    114.1 KB · Views: 16
  • 20241107_195615[1].jpg
    20241107_195615[1].jpg
    105.3 KB · Views: 17
  • 20241107_195508[1].jpg
    20241107_195508[1].jpg
    83.7 KB · Views: 14

Latest posts

Forum statistics

Threads
44,157
Posts
950,588
Members
36,271
Latest member
jstewart7501
Top