82 Dodge D 350... Hate to ask....

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

legopnuematic

legopnuematic

Licensed Junk Dealer
Supporting Member
Joined
Oct 27, 2016
Posts
2,506
Reaction score
6,482
Location
MO
First Name
Spencer
Truck Year
1971, 1̶9̶7̶4, 1976, 1979,1̶9̶8̶5, 2002
Truck Model
Dart Swinger, Sierra 10, C10 Cheyenne, C10 Big Ten, Silverado 10, Ram 2500
Engine Size
225/6, 350 c.i., 350 c.i., 5.9l Cummins
LA 360's are solid plants, they respond very nicely to standard hop up procedures. late LA's (1985ish) were roller cam engines and then the Magnum engines were all roller engines and featured a set of redesigned heads (think of it like vortec heads for sbc's) Magnum engines can be reverted to LA trim with changing the front cover and adding an eccentric to run a mechanical fuel pump from.
 
Turbo4whl

Turbo4whl

Supporting Member
Supporting Member
Joined
Oct 30, 2019
Posts
3,126
Reaction score
7,255
Location
Downingtown, PA
First Name
Wayne
Truck Year
1974
Truck Model
Jimmy
Engine Size
350
Back in the day our company had lots of those Dodges. Yes as stated, the 360 is a fine engine. Two things I remember that are important about the engine. The distributor rotor can get rusted in place. If you try to pry it off, sometimes you will bend the distributor shaft. After you finish the tune-up and go to start the engine it will not fire on all the cylinders.

The trick to remove a stuck rotor, is to take a small ball-peen hammer, strike the rotor straight down from the top and it breaks into pieces.

The other issue to be aware of, if it is fitted with the thermoquad carburetor, the plastic(Bakelite) housings warp.

On the body, check the firewall around the master cylinder, they crack. Also the radiator support can crack. The operators would complain about spongy brake pedal. Then after looking at all the brakes, find the firewall would flex 3/4 of an inch when pushing the brake pedal. This was so common it became a check point on the PM list. These are easy fixes for you, as you are a welder.
 
I

idahovette

Full Access Member
Joined
Aug 7, 2016
Posts
7,269
Reaction score
15,872
Location
Weiser Idaho
First Name
Perry
Truck Year
1975-1979
Truck Model
K20-K10
Engine Size
350
Turbo4whl said:
Back in the day our company had lots of those Dodges. Yes as stated, the 360 is a fine engine. Two things I remember that are important about the engine. The distributor rotor can get rusted in place. If you try to pry it off, sometimes you will bend the distributor shaft. After you finish the tune-up and go to start the engine it will not fire on all the cylinders.

The trick to remove a stuck rotor, is to take a small ball-peen hammer, strike the rotor straight down from the top and it breaks into pieces.

The other issue to be aware of, if it is fitted with the thermoquad carburetor, the plastic(Bakelite) housings warp.

On the body, check the firewall around the master cylinder, they crack. Also the radiator support can crack. The operators would complain about spongy brake pedal. Then after looking at all the brakes, find the firewall would flex 3/4 of an inch when pushing the brake pedal. This was so common it became a check point on the PM list. These are easy fixes for you, as you are a welder.
Click to expand...
About the body, sometimes the doors fall off!!!.....LOL
 
wanderinthru

wanderinthru

Full Access Member
Joined
Jul 23, 2020
Posts
1,174
Reaction score
2,079
Location
Mid Point Route 66
First Name
Shakey
Truck Year
81, 70, 75, 84, 89
Truck Model
K 10, C 30, K 20
Engine Size
350
Turbo4whl said:
Back in the day our company had lots of those Dodges. Yes as stated, the 360 is a fine engine. Two things I remember that are important about the engine. The distributor rotor can get rusted in place. If you try to pry it off, sometimes you will bend the distributor shaft. After you finish the tune-up and go to start the engine it will not fire on all the cylinders.

The trick to remove a stuck rotor, is to take a small ball-peen hammer, strike the rotor straight down from the top and it breaks into pieces.

The other issue to be aware of, if it is fitted with the thermoquad carburetor, the plastic(Bakelite) housings warp.

On the body, check the firewall around the master cylinder, they crack. Also the radiator support can crack. The operators would complain about spongy brake pedal. Then after looking at all the brakes, find the firewall would flex 3/4 of an inch when pushing the brake pedal. This was so common it became a check point on the PM list. These are easy fixes for you, as you are a welder.
Click to expand...

Good information, I do appreciate it. Going to look at it once this weather clears out. The wench interest me as much as the whole truck, prob give less for this whole rig than I can find the winch for.
Appreciate it!!
 
You must log in or register to reply here.

Similar threads

S
1994 Dodge Ram Van 350
2
Replies
20
Views
1K
SirRobyn0
S
C
350 or LS
2 3
Replies
36
Views
3K
Vbb199
Vbb199
Oldbear42
New to me '82 Chevy C20
Replies
14
Views
1K
Long Rider
Long Rider
BigT
New to the forum, but not to Squarebodies...
2 3
Replies
30
Views
1K
CapAhab
C
Jawzjeep
About to get my first cummins truck.
2
Replies
26
Views
2K
squaredeal91
squaredeal91

Latest posts

Forum statistics

Threads
44,162
Posts
950,642
Members
36,276
Latest member
2manysquares2care
Top