Rusty Nail
Full Access Member
- Joined
- Jan 29, 2015
- Posts
- 10,041
- Reaction score
- 10,138
- Location
- the other side of the internet
- First Name
- Rusty
- Truck Year
- 1977
- Truck Model
- C20
- Engine Size
- 350sbc
Redo bigblock.
No LS swap.
No LS swap.
79 CC C-30. Ls swap or redo big block?
- Thread starter beest
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
beest
Full Access Member
- Joined
- Feb 13, 2015
- Posts
- 109
- Reaction score
- 29
- Location
- indiana
- First Name
- matt
- Truck Year
- 84
- Truck Model
- k10
- Engine Size
- 350
Alrighty yall, got a few questions.
We got the 454 pulled out of the dually. Tore it down to the short block. Now more questions.
What are these sleeves? This head has been replaced at some point. When i pulled the valve covers, one of the pushrods was out of its home in the rocker too. Doesnt look bent. Lifter looks ok. Wtf?
Sent from my SM-G920P using Tapatalk
We got the 454 pulled out of the dually. Tore it down to the short block. Now more questions.
You must be registered for see images attach
What are these sleeves? This head has been replaced at some point. When i pulled the valve covers, one of the pushrods was out of its home in the rocker too. Doesnt look bent. Lifter looks ok. Wtf?
Sent from my SM-G920P using Tapatalk
beest
Full Access Member
- Joined
- Feb 13, 2015
- Posts
- 109
- Reaction score
- 29
- Location
- indiana
- First Name
- matt
- Truck Year
- 84
- Truck Model
- k10
- Engine Size
- 350
You must be registered for see images attach
Any idea why one valve would be white like this? Just one?
You must be registered for see images attach
Looks like itll need valves...
Sent from my SM-G920P using Tapatalk
Rusty Nail
Full Access Member
- Joined
- Jan 29, 2015
- Posts
- 10,041
- Reaction score
- 10,138
- Location
- the other side of the internet
- First Name
- Rusty
- Truck Year
- 1977
- Truck Model
- C20
- Engine Size
- 350sbc
Wow. That exhaust valve must have been really hot!
And lean.
Did you just save yourself a rebuild!?
I am not familiar with those sleeves...but they suck. The spring seat was relieved? That would inhibit oil flow? Which serves to cool?
Is the white valve head the same one with the sleeves?
I bet it is.
AND!
Omfg @ orange silicon to seal a valve cover. RUNNNN!
YEAH. That worked great i'm sure...no tellin what other corners were cut. Better rebuild it!
You see that valve has no keeper on it.. it didn't work..that's prolly the white one.
It will run a lot better with a quality head service. Too bad you didn't look into it deep enough to figure that out before pulling the motor but, whatever.
And lean.
Did you just save yourself a rebuild!?
I am not familiar with those sleeves...but they suck. The spring seat was relieved? That would inhibit oil flow? Which serves to cool?
Is the white valve head the same one with the sleeves?
I bet it is.
AND!
Omfg @ orange silicon to seal a valve cover. RUNNNN!
YEAH. That worked great i'm sure...no tellin what other corners were cut. Better rebuild it!
You see that valve has no keeper on it.. it didn't work..that's prolly the white one.
It will run a lot better with a quality head service. Too bad you didn't look into it deep enough to figure that out before pulling the motor but, whatever.
beest
Full Access Member
- Joined
- Feb 13, 2015
- Posts
- 109
- Reaction score
- 29
- Location
- indiana
- First Name
- matt
- Truck Year
- 84
- Truck Model
- k10
- Engine Size
- 350
The white valve is the head with those **** sleeves on it.
The valve tip is from the other head. The keepers are in there. It just looks like the rocker wore the tip of the valve stem off.
It ran, but shi**y. I was just gonna inspect and reseal the ****. But i need too look deeper.
The valves have hit the pistons on the right bank at some time, that could explain the replaced head.
Good thing i got this truck cheap AF. The engine is gonna need some love.
Sent from my SM-G920P using Tapatalk
The valve tip is from the other head. The keepers are in there. It just looks like the rocker wore the tip of the valve stem off.
It ran, but shi**y. I was just gonna inspect and reseal the ****. But i need too look deeper.
The valves have hit the pistons on the right bank at some time, that could explain the replaced head.
You must be registered for see images attach
Good thing i got this truck cheap AF. The engine is gonna need some love.
Sent from my SM-G920P using Tapatalk
Rusty Nail
Full Access Member
- Joined
- Jan 29, 2015
- Posts
- 10,041
- Reaction score
- 10,138
- Location
- the other side of the internet
- First Name
- Rusty
- Truck Year
- 1977
- Truck Model
- C20
- Engine Size
- 350sbc
Daaannggg!
That is almost a hole in the piston dude. It's not reuseable.
A rebuild is certain.
That is almost a hole in the piston dude. It's not reuseable.
A rebuild is certain.
beest
Full Access Member
- Joined
- Feb 13, 2015
- Posts
- 109
- Reaction score
- 29
- Location
- indiana
- First Name
- matt
- Truck Year
- 84
- Truck Model
- k10
- Engine Size
- 350
Im looking at machine shops in my area on the interweb meow.
Weve reused pistons in neons with waay worse gouges from when timing belts snapped and bent all the valves.
But i agree, it needs new ones. It needs more compression too.
Sent from my SM-G920P using Tapatalk
Rusty Nail
Full Access Member
- Joined
- Jan 29, 2015
- Posts
- 10,041
- Reaction score
- 10,138
- Location
- the other side of the internet
- First Name
- Rusty
- Truck Year
- 1977
- Truck Model
- C20
- Engine Size
- 350sbc
Yeah sure you could re-use it, but there's no reason to.
I wouldn't put that in MY truck and since that's the case, I wouldn't sell you the repair that contained that piston because i'm only going to fix it once.
I wouldn't put that in MY truck and since that's the case, I wouldn't sell you the repair that contained that piston because i'm only going to fix it once.
Honky Kong jr
Super Sarcastic Man
- Joined
- Jun 14, 2016
- Posts
- 14,968
- Reaction score
- 9,833
- Location
- Denver,PA
- First Name
- J-me
- Truck Year
- 87
- Truck Model
- V10
- Engine Size
- Lil BB 407
That little ding isn’t gonna hurt anything. Smooth it out so it’s not a hot spot. I hope you’s aren’t taking about the deeper one. Lol that kinda has to be there. The canted valve thing and all. Lol
Last edited:
Similar threads
