4L60e Torque Converter in a Bind

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

jfkelley

Full Access Member
Joined
Apr 14, 2019
Posts
65
Reaction score
15
Location
Oklahoma City
First Name
John
Truck Year
1976
Truck Model
K10
Engine Size
350
Before I mate the transmission to the engine I filled the TC up with ATF..I put the torque converter on turned it until it three times until I heard three clunks ..I have no idea how it got in a bind but between installing it on the engine and putting the engine in it binded up ..Put break over bar on harmonic balancer gave it a couple cranks and heard a ****!! My heart fell into my stomach ..Idk what happen but but TC spins freely now ..hope I didn’t f up anything up ..Like to hear your thoughts on this ? Thanks in advance
 

yevgenievich

Full Access Member
Joined
Mar 1, 2014
Posts
4,819
Reaction score
3,400
Location
Place
First Name
Name
Truck Year
Year
Truck Model
Model
Engine Size
Size
Might have snapped the pump drive in the transmission.
Edit: clarification
 
Last edited:

jfkelley

Full Access Member
Joined
Apr 14, 2019
Posts
65
Reaction score
15
Location
Oklahoma City
First Name
John
Truck Year
1976
Truck Model
K10
Engine Size
350
I measured from flywheel to TC Tab and got .136.. ..I read that it needs to be between 0.60-.0.185..You guys think I’m ok?
 

Matt69olds

Full Access Member
Joined
Jan 8, 2018
Posts
2,451
Reaction score
3,819
Location
Central Indiana
First Name
Matt
Truck Year
81
Truck Model
GMC 1/2 ton
Engine Size
455 Olds
Don’t start it, it’s almost a certainty the converter slipped out of the pump while installing it. The pump rotor is junk. Right now all you will need is a rotor, start it you will need a pump, converter and most likely a complete overhaul to get the shrapnel out.
 

Matt69olds

Full Access Member
Joined
Jan 8, 2018
Posts
2,451
Reaction score
3,819
Location
Central Indiana
First Name
Matt
Truck Year
81
Truck Model
GMC 1/2 ton
Engine Size
455 Olds
Next time, slowly tighten the bellhousing bolts, stopping every few turn to make sure the converter spins freely. Anytime the converter locks or binds, you need to stop and find out why.
 

jfkelley

Full Access Member
Joined
Apr 14, 2019
Posts
65
Reaction score
15
Location
Oklahoma City
First Name
John
Truck Year
1976
Truck Model
K10
Engine Size
350
Thank Matt ..Lesson learned and I was almost done with the swap ..Now have to pull transmission and transfer case ..So disappointed..
 

yevgenievich

Full Access Member
Joined
Mar 1, 2014
Posts
4,819
Reaction score
3,400
Location
Place
First Name
Name
Truck Year
Year
Truck Model
Model
Engine Size
Size
Should have put a warning on do not actually try checking pressure in above reply if suspecting pump issue
 

jfkelley

Full Access Member
Joined
Apr 14, 2019
Posts
65
Reaction score
15
Location
Oklahoma City
First Name
John
Truck Year
1976
Truck Model
K10
Engine Size
350
FYI I should have included this in the original post : The TC was not bolted to the Flex plate when I turned the Engine by using the Break-over bar
 

jfkelley

Full Access Member
Joined
Apr 14, 2019
Posts
65
Reaction score
15
Location
Oklahoma City
First Name
John
Truck Year
1976
Truck Model
K10
Engine Size
350
These are pics of where the TC is now ..The. Lot in the second one is barely threaded in ..Do
You think I need spacers ?
 

Attachments

  • 4B26D858-490C-434F-B3E1-D2A9FC2F20C9.jpeg
    4B26D858-490C-434F-B3E1-D2A9FC2F20C9.jpeg
    76.6 KB · Views: 61
  • 78317A99-0DB5-47D0-93D9-33CE154F91BC.jpeg
    78317A99-0DB5-47D0-93D9-33CE154F91BC.jpeg
    68.4 KB · Views: 54

Matt69olds

Full Access Member
Joined
Jan 8, 2018
Posts
2,451
Reaction score
3,819
Location
Central Indiana
First Name
Matt
Truck Year
81
Truck Model
GMC 1/2 ton
Engine Size
455 Olds
The rule of thumb is 1/8 to 3/16 inch of converter pullout. In other words, with the converter buried in the pump as far as it will go, you should have 1/8-3/16 gap between the mounting tabs and the flexplate. You can usually get away with a little more than 3/16, but ideally you should use some washers to take up some space.

Did you reseat the converter, or actually remove it and inspect the pump? If the converter wasn’t seated and you tighten the bellhousing bolts, most likely the pump rotor is broken. Bad (and expensive!!) things WILL happen if you start it like that.
 

jfkelley

Full Access Member
Joined
Apr 14, 2019
Posts
65
Reaction score
15
Location
Oklahoma City
First Name
John
Truck Year
1976
Truck Model
K10
Engine Size
350
@Matt69olds..I measured from flywheel to TC Tab and got .136 that night .. ..The next morning I went out and was turning the TC by hand and pushing towards the rear end & it seated my gap is a little wider now it’s spinning in the bell housing by hand ..I can see it’s in the pilot bushing and I hear some clack clack’s when I move the TC back-and-forth no grinding noise ..I have another transmission on stand by
 

Latest posts

Forum statistics

Threads
44,163
Posts
950,648
Members
36,276
Latest member
2manysquares2care
Top