Search results

  1. Rustybucket73

    DIY Junkyard Wiper Motor and Intermittent Module Retrofit/Upgrade

    I honestly don't know what that is either. It's probably some accent lighting for the wiper switch when the headlights are on.
  2. Rustybucket73

    DIY Junkyard Wiper Motor and Intermittent Module Retrofit/Upgrade

    I can't use the Camaro speedo because its cable driven. My '73 has a 5.3/4L80E so I needed an electronic speedo, using the 80-91 squarebody cluster was the easiest option. I put a voltmeter gauge in the original oil pressure gauge location, but it's wired to read my fuel level. I just need to...
  3. Rustybucket73

    DIY Junkyard Wiper Motor and Intermittent Module Retrofit/Upgrade

    Yup, mid-80's V8 Camaro tach in a '89-91 Squarebody cluster with electronic speedometer, all in a '73 C10
  4. Rustybucket73

    DIY Junkyard Wiper Motor and Intermittent Module Retrofit/Upgrade

    Got some time to put the interior back together. Hard to tell that anything has been modified at all.
  5. Rustybucket73

    DIY Junkyard Wiper Motor and Intermittent Module Retrofit/Upgrade

    The only thing holding me back from releasing this as a kit would be the fabricated arm. Even if I could get the arm laser cut and bent, that would still leave the buyer needing to transfer and weld in the pivot ball.
  6. Rustybucket73

    DIY Junkyard Wiper Motor and Intermittent Module Retrofit/Upgrade

    Good News! The wiper motor kit is in and its working great. Here's quick video of the motor in action: Quick explanation of what's going on in the video. 1. Shot of the motor and the moving linkage 2. Low speed 3. High speed 4. Fast intermittent 5. Slow intermittent
  7. Rustybucket73

    DIY Junkyard Wiper Motor and Intermittent Module Retrofit/Upgrade

    The Toyota wiper motor has a tapered knurled round shaft instead of the slotted hole of the Chevy wiper motor. I decided to cut and reuse the Toyota wiper arm part with the corresponding knurled hole because hole has around 14 degrees of taper and I couldn't find a reamer with that angle on it.
  8. Rustybucket73

    DIY Junkyard Wiper Motor and Intermittent Module Retrofit/Upgrade

    So here is the motor to linkage arm that I just finished welding up. Showing the original arm below for comparison. Not the best welds in the world, but the piece is solid and should be ok for what I'm using it for. It'll look a lot better after some grinder action and some paint. Hole to...
  9. Rustybucket73

    DIY Junkyard Wiper Motor and Intermittent Module Retrofit/Upgrade

    I don't think this this will end up being a problem. Just holding both of the motors, the Camry motor feels 1.5 to 2x heavier. Probably a lot more copper windings for the Camry motor and a lot more torque.
  10. Rustybucket73

    DIY Junkyard Wiper Motor and Intermittent Module Retrofit/Upgrade

    This all started when the wiper motor in '73 failed. Tried turning the wiper motor arm by hand, it was completely seized. I was already looking at upgrading to intermittent wipers and sourcing a steering column, but I thought I could come up with something better. I couple things I wanted to try...
  11. Rustybucket73

    Arduino powered fuel injector tester.

    Honestly, its probably fine. But since it doesn't cost me anything to flow them, I'll try and get it a bit closer. I can always sell a close set of 4 to the honda guys since they're starting to use the decapped injectors now, and use that cash to get some more injectors.
  12. Rustybucket73

    Arduino powered fuel injector tester.

    Finished making my flow rig and flowed about 20 injectors, still don't have a perfectly matched set. The closest set of 8 is within 2.5% dynamically and perfect on the static test. Gotta go back to the junkyard and get some more. How everything is wired up on the back, might be a little...
  13. Rustybucket73

    Arduino powered fuel injector tester.

    I'm doing the same thing, just built the frame today. Still waiting on parts but getting ready for that decapped goodness. I'll be using Dale's code and modified the dynamic test so it goes through the following ranges: 600rpm @85%DC = 30 low 170 high For 5 Sec = 25 cycles 1200rpm @85%DC...
  14. Rustybucket73

    5.3 LS w/4L80 Mystery Noise

    I think the problem was that air was trapped in the cooler since it was being filled from the top. Once I flipped the lines around and filled the cooler from the bottom, all the air was able to be purged and properly lubricate whatever is on the cooler return side of the transmission.
  15. Rustybucket73

    LS swap questions

    I agree, thats the safer option. But around here, people want $750-1000 for just a 4.8 w/accessories, no trans and 100k+ miles. I wanted to do my swap on a budget, so I took a chance.
  16. Rustybucket73

    LS swap questions

    Definitely possible to do it for close to $1000. I started with a 73 SB with a 350/350 Got as much as I could from the junkyard, especially on 50% off days. 5.3 w/ harness, pcm, & accessories was around $250, found a broken valve spring so add $7 Got a 4l80e @50% off for $80 lol Put a HD2 kit...
  17. Rustybucket73

    5.3 LS w/4L80 Mystery Noise

    So I found a problem with my trans cooler plumbing. It was like this: Re-plumbed it with the fluid return coming out the top like this: Don't know if that was the reason for the noise, but the noise is gone now. Crossing my fingers.
  18. Rustybucket73

    5.3 LS w/4L80 Mystery Noise

    Want to update the thread. Took the trans off the motor and inspected the flex plate. No cracks around the crank bolt holes or anywhere else on the flex plate. Didn't see any rub marks on the inside of the bell housing or on the engine behind the flex plate. Re-torqued all the crank/flex...
  19. Rustybucket73

    5.3 LS w/4L80 Mystery Noise

    Yeah, it has the 6.0 flexplate and spacer
  20. Rustybucket73

    5.3 LS w/4L80 Mystery Noise

    Ok, thanks. I'll check it out
  21. Rustybucket73

    5.3 LS w/4L80 Mystery Noise

    I guess I can take that as everything is fine?
  22. Rustybucket73

    5.3 LS w/4L80 Mystery Noise

    Just finished up budget LS swap on a '73 C10. Bone stock 5.3 from a suburban 4l80e with a HD2 kit, stock converter Has a weird noise when ever I rev up to around 2500rpm while parked. Noise also comes back around the same rpm while driving. Converter is seated all the way in the pump...

Latest posts

Forum statistics

Threads
44,166
Posts
950,716
Members
36,281
Latest member
gsexton
Top