Search results

  1. 85K304SPD

    Finding Serpentine Belt Lengths

    I just went through this. Trial and error. A few MMs makes a big difference. Take the belt that you have, and the measurement you make with the measuring tape, and try to figure out which one you need, see what the parts store has in stock and get the closest one and go try it out. If its the...
  2. 85K304SPD

    Sanderson BB8-P headers on a 454 in a crew cab dually

    I've got a set of those headers on my SHOP FLOOR. I don't think that they will fit on anything, but the break in stand. (I fell for it too) I just used the stock manifolds, and they work great. No burnt plug wires, header leaks, etc...
  3. 85K304SPD

    Header Gaskets

    Remflex all the way!!
  4. 85K304SPD

    Brake Booster Vacuum re-location?

    Run your brake booster to the one on the back of the carburetor and get a combination vacuum fitting for the manifold for the PCV, heater control and automatic transmission. Get a short one so it clears the bowl on the carb. You may need a spacer under the carb. Something like that.
  5. 85K304SPD

    Transmission grinds going into L or R

    If you are not moving, with the clutch in, they should not grind. If you are trying to get it into L or R with it rolling, they will probably grind a little. If they grind when you are not moving, your clutch will probably need adjusting or replaced.
  6. 85K304SPD

    Transmission grinds going into L or R

    So your truck has the 4 speed overdrive transmission ,NP A 833, or the 4 speed with the granny gear low? SM 465
  7. 85K304SPD

    Speedo cable length for 81 c10 6 cylinder saginaw

    I just bought one from O'reillys and it was the right length. Works great and was only like $13. You might give them a try.
  8. 85K304SPD

    Trailering your square body

    Make sure that you have good tires on the trailer. Load it up and go. It sounds like you have a good truck for the job. Take your time and tie it down good, so it doesn't bounce. Hope for the best, be ready for the worst. Do it now, before it gets too hot, and it will be easier on you and your...
  9. 85K304SPD

    K20 454 truck engine build

    Don't "over cam" it. You will be happier in the long run with something on the "smaller" side than something real long on duration. Melling MTC 6 (good old fashioned RV cam) looks good for a 4 x 4. The "268" advertised duration cams would be the "biggest" that I would use. Off idle grunt, up...
  10. 85K304SPD

    Remove accessories from this old truck?

    The suburban looks good, the yellow truck is a little bit impractical. I'm not sure which vehicle you are working on or asking about.
  11. 85K304SPD

    Power steering fluid .. what type ?

    I guess that I learned something on this one... I don't have any classic vehicles with automatic transmissions, so I will stick with the power steering fluid. Thanks for the education.
  12. 85K304SPD

    Power steering fluid .. what type ?

    I use power steering fluid for power steering. I have had bad luck putting ATF in power steering pumps. There must be a reason that they call it power steering fluid and the other one is called automatic transmission fluid. The front of the container tells you which fluid goes in which system. I...
  13. 85K304SPD

    distributor removal

    It makes it easier to put back together. Like Hucked said, that is a good thing to start with, before you pull the distributor, put it on TDC, or at least real close.
  14. 85K304SPD

    1981? 350 in a C20 - Vacuum/sensor questions

    Vacuum advance, heater, pcv, brake booster. That is about all you need. All that other stuff is basically ways to regulate the advance and warm air, I think. Lots of little parts to replace, if you have to have them.
  15. 85K304SPD

    Wiper Blade size

    I use the ones that the book says at the parts store. It rarely rains here, so I never gave it much thought beyond that. They usually just sun rot and when it does rain, you have to look through a spot that they miss, or go buy new ones. But next time, I will think about some longer ones, maybe.
  16. 85K304SPD

    95 Chevy water in passenger floor board

    Heater core. Mine was dripping out of the bottom of the cab. I had to loop the heater hoses... for now... Its warm enough, no heater necessary for another 6 months. The carpet is dry but kind of oily now.
  17. 85K304SPD

    edelbrock avs2 650

    I have to pump mine about 20 times to start it cold. When it is warm, usually have to pump it a couple of times. It's not fuel injection. 1406, Edelbrock pump, air gap intake. For some reason they just wont hold fuel. I guess it evaporates. So I would say that yours is "normal".
  18. 85K304SPD

    tighter steering

    If you think a C20 is hard to turn sharp, you should try a K30 with a Dana 60 front axle... It makes a K20 seem like a sports car. Like Hucked said, Nature of the "Beast".
  19. 85K304SPD

    Thermostat

    195
  20. 85K304SPD

    Sad Discovery: GM 10 Bolt Fails

    What happened?
  21. 85K304SPD

    New to Square Body Trucks, not trucks in general

    I would make sure it runs good before I did anything to it. Taking it somewhere to fix that sounds expensive, but if that is what you have to do...
  22. 85K304SPD

    New to Square Body Trucks, not trucks in general

    Welcome. What are you wanting to do with it, work truck, daily driver, show truck? I dont have any experience with fuel injection wiring, but if you can get it straightened out, it might be worth keeping on there. How does it run?
  23. 85K304SPD

    Top Radiator Clamps

    There is a few different sizes of radiators for these squares. Height and width differences. Brackets, shrouds, hoses, hold downs... dont forget the little rubber saddle things that they sit in... There is more variables than I ever thought there could be.
  24. 85K304SPD

    Top Radiator Clamps

    On my '85 big block, with the tall wide radiator, it is one solid piece that holds down the radiator. What radiator do you have?
  25. 85K304SPD

    Want to build a good horsepower, good fuel economy engine for a 1978 c20 with stock 350. I don't know much and need help.

    The place to start would be a good compression test. You need to determine if the engine needs a rebuild before you add a bunch of stuff to the outside. Assess what you have and determine what you want it to be in the end, as well as what your budget is and do the math and go from there.

Latest posts

Forum statistics

Threads
45,429
Posts
983,220
Members
38,462
Latest member
HowPoison
Top