Search results

  1. 6

    1987 3/4 ton crew cab

    Great truck, nice wheels - and what are they ?
  2. 6

    what ya'll think about my engine set-up

    Just run with it. Does it run pretty good ? Any spark knock ? 10-1 with iron heads , a heavy vehicle , and a small duration cam are a recipe for spark knock. Make sure to fill with premium fuel only !
  3. 6

    Exhaust Opinion

    I always run an H-pipe and always build my exhaust - but buy a pre-made H-pipe from Summit. If you'd like a nicer/quieter sound the large case Dynomax turbo mufflers work great and cost less than flowmasters.
  4. 6

    water got in engine... help please

    Make sure to check over the 305 before going thru the trouble of stabbing it in. Check the gaskets and check for timing chain slack, easier to replace something now instead of after installation. Nowadays it's probably best to check the cam and lifters too. Not the fastest or cheapest way to...
  5. 6

    Stock replacement tbi crate

    A stock engine will run fine on 87 with it's stock chip.
  6. 6

    water got in engine... help please

    You mentioned that the "engine won't crank" and that it "turns over freely" , so does it turn over too easily with the plugs installed ( as if there is no compression ), but doesn't fire and attempt to start ?? You can pull a spark plug then hold a finger over the hole while cranking to see if...
  7. 6

    oldsmobile 350 headers...in a square

    Go to www.RealOldsPower.com and ask there. It has been too long for me to remember if there were any that fit . I'm sure there are more there that have put Olds engines into trucks than what you'd find here.
  8. 6

    Turbo 350 Information and Facts

    One minor detail which doesn't matter in a th350 thread is that the th400 and the Muncie M22 (Rockcrusher) share the same yoke , but not the th350 and the M22 as was mentioned as being the same. M20 and M21 - yes, same as a th350. I'm old but do remember that.
  9. 6

    Found on eBay Listings

    Kan't believe it !! Holy snotrockets batman !!
  10. 6

    WTB 4x4 crew cab

    I'll have to take some newer and better pics with my camera, the snow will be melting soon too to take pics. Just not tomorrow. ..but ya.. it happened... I have two old pics with the bed on. Send me an email and I'll get them sent back to you and you can post them, because I can't.
  11. 6

    Poor Man Valve Job

    Wrap them in foil , no ..I've not tried it but it may work ! Probably won't do anything for the stink.....
  12. 6

    WTB 4x4 crew cab

    Mines a regular 4X4 dually 3+3 without a bed, runs and drives . Original 454 still in it , T400 trans. Black exterior, red interior. I have a 9' flatbed for but not on it. Indianapolis
  13. 6

    Olds 350

    List Olds parts here ; www.RealOldspower.com (hardcore racers, collectors, and graybeards with A-body's), or here ; www.Oldspower.com ( younger guys , lotsa 307's & 350's , G-body cutlass' )
  14. 6

    truck randomly stalls out, but runs perfect otherwise. help me out here

    Don't rule out any ignition problems either. A bad/weak coil , arching thru the rotor , a failing module, ...
  15. 6

    Vortec Heads

    If you get close-by hit me up ! I'm sure we could work something out. I'm in the phonebook under "Garage Door Service of Indiana, Inc." in Indpls. (not to be confused with any other Co's with a similar name(s). 317-322-xxxx ( 8 to 5 Mon - Fri) I'm on the SE side of Indy when I'm home or in...
  16. 6

    Olds 350

    '68 to ''76 block , '71 heads. You'll notice it has very thick cyl walls. Easy to build ; 362 ci , 374ci , with this block and a stock cast crank, or 385ci to 396ci with a older steel crank and a lot of machine work. Heads can accept up to a 2.10" intake valve, (bigblock 2.072" & 1.71"...
  17. 6

    350 Engine upgrades

    Yes use the vortec heads and don't consider anything else until you can afford aftermarket heads. Vortecs are perfect for what you're wanting. Buy a good/used Performer vortec intake for cheap, buy a small cam and lifter set (once you get the correct info on which cam, not necessarily from...
  18. 6

    Vortec Heads

    Heading to Indy for anything ? I'd take the used set for $100, but shipping anything heavy is getting too pricey. I think you have other stuff for sale I'd use too. Thanks, Tim
  19. 6

    Olds 350

    I can tell ya, but it erased a long post I typed. Post the casting numbers and I'll tell you what they are and perhaps be able to help you sell them. Is there a re "D" or "DX" cast on the side of the block ? Number on the corner of each head (4,5,6,7,etc..), casting number on the cast crank...

Latest posts

Forum statistics

Threads
44,416
Posts
957,113
Members
36,752
Latest member
78 squarebody
Top