Search results

  1. Jarhead79

    Holley or edelbrock?

    Besides shipping etc what would be the cost for swapping one versus rebuilding mine!?
  2. Jarhead79

    Holley or edelbrock?

    I'll check when I get home and let you know, I've had quads before but have only rebuilt one, didn't get it quite right and had to have a mechanic redo it. Lol that was 23yrs ago so I've learned a little more since then but don't want to tinker too much and have to spend a ton of cash. Carbs...
  3. Jarhead79

    Holley or edelbrock?

    After startup in the morning after 4/5 pumps on gas it smells rich and has some popping in the exhaust, probably due to pumping it but it still smells rich but when it's at about 190 degrees it doesn't smell as bad but you can still hear the exhaust, sounds like bubbles popping is how I can...
  4. Jarhead79

    Holley or edelbrock?

    It does run good, a little rich, but I'm not sure how to adjust the quad. Are there any tweaks to adjust the fuel?
  5. Jarhead79

    Holley or edelbrock?

    It does run good, a little rich, but I'm not sure how to adjust the quad. Are there any tweaks to adjust the fuel?
  6. Jarhead79

    Holley or edelbrock?

    Ok I have three choices here, I have a quadrajet on my truck, works good, have been given a Holley 750 and a spacer for free but the Holley needs rebuilt, or should I say hell with it and get an edelbrock? I know I should probably just keep the quadrajet but I'm not sure if any is better than...
  7. Jarhead79

    Fix Slamming Doors - Striker Door Latch Repair

    I took a roll of black tape and wrapped it around the striker, fixed it for now, you have to remember though that those plastic pieces were put on there somehow so I'm wondering if removing the striker would be easy
  8. Jarhead79

    Gauge cluster

    The numbers on the back are as follows: 25088586 ped-1 8811-3 92 14 56
  9. Jarhead79

    Gauge cluster

    Here's another pic
  10. Jarhead79

    Gauge cluster

    I picked this up without paying close attention to which year trucks this would fit, can anyone use it? Not sure what a good price would be for it?
  11. Jarhead79

    Exhaust ideas!?

    I'm pretty sure I'm going with a 40 series muffler. I've used a company before called jones performance, knock off of flow aster 40, but sounds better and is actually better made in my opinion plus it's only $40 bucks a muffler. I don't want obnoxious but I used these on my 03 Dodge Ram and my...
  12. Jarhead79

    Exhaust ideas!?

    I'll check this week on the mufflers it's true duals with stock manifolds a d I'm guessing about 2" or so exhaust into what I think are walker brand mufflers. Will get pics if I can
  13. Jarhead79

    Exhaust ideas!?

    Mines more a daily driver, but it's just too quiet, I don't want cackling exhaust but I want more muscle car, just not sure if I should do single exhaust or not, My truck is so quiet that I can't hear it in the cab, died on me one day and I didn't even feel it
  14. Jarhead79

    Exhaust ideas!?

    Need advice on exhaust, as far as exhaust I have true duals but oddly enough one pipe runs over the trans crossmember, one runs under it on passenger side. I'm trying to decide if I should do single exhaust with a y pipe or keep it true duals? I'm wanting to redo the exhaust since the back half...
  15. Jarhead79

    Long tube or short tube headers?

    So longtubes are what I should go with then also? What primary size should I look for?
  16. Jarhead79

    Long tube or short tube headers?

    So say I've got a stock 350 2 wheel drive and want to go headers, say 2.5 inch dual exhaust, would it matter going short versus longtube?
  17. Jarhead79

    Adjusting the ignition switch in column?

    I'll give it a look, previous owner said he adjusted it like this for a theft deterent, but I feel like I'm going to rip the ignition cylinder out every time I twist it to start! Lol
  18. Jarhead79

    Adjusting the ignition switch in column?

    How do I adjust the rod etc so I don't have to forcefully turn the key to start the truck, it won't start unless I turn the key all the way forward and push as hard as I can!
  19. Jarhead79

    Wanting to go posi.

    I'll send them an email, my truck isn't by any means a race truck but I'm building for street driving and occasional drag strip fun nights. Lol eventually a motor upgrade maybe next year!
  20. Jarhead79

    Wanting to go posi.

    What's the price on those, any links to them?
  21. Jarhead79

    Wanting to go posi.

    I wasn't sure if I cod just buy the internal parts or not but thought if I could find an d psi rearend to swap in than that would be easiest, I've messed with gears etc a little but haven't tackled the install fully. I know some times it's a snap, sometimes it's a PITA! Lol
  22. Jarhead79

    Wanting to go posi.

    What should I be on the lookout for as far as replacement for my single trac rear with 3:73 gears(I think) I still need to check them and see. Not sure if the rear has ever been replaced or not but he truck has had a motor and trans put put in. I've got a th350 trans and basically a reman 350 in...
  23. Jarhead79

    Fair price to pay for 14BFF and Dana 60 Combo

    I'm wanting to go with a posi rear Oops wrong post!
  24. Jarhead79

    Best place to get interior panels and trim pieces?

    Most pieces are, headliner I can redo, carpet will be easy to switch out, the metal door trim pieces at the bottom of the door are junk and bent and missing chunks of metal, under dash has been painted black which is fine but they didn't do a good job, looks like rattle can, but even it could be...
  25. Jarhead79

    Best place to get interior panels and trim pieces?

    Just curious if it'd be best to just repaint all my interior pieces or order all new ones? I'm looking for all the metal/ plastic trim pieces in the truck, except the door panels, I'm still trying to decide to salvage mine and redo them or cut them up and make my own!

Latest posts

Forum statistics

Threads
44,173
Posts
950,868
Members
36,288
Latest member
brentjo
Top