Search results
-
F
What have you done to your square lately??
Pushed it into a black hole! Tired of the issues lol Sent from my iPhone using Tapatalk -
F
Just another guy from Ohio....
Seville Ohio here! Welcome. Sent from my iPhone using Tapatalk- fmxr47
- Post #25
- Forum: Introduction
-
F
What have you done to your square lately??
Stared at it for a while [emoji1303] Sent from my iPhone using Tapatalk -
F
What have you done to your square lately??
Finally installed my dash with the new plastic cap over it. Sent from my iPhone using Tapatalk -
F
Howdy y'all!
Welcome, there are a lot of helpful individuals on this forum! Sent from my iPhone using Tapatalk- fmxr47
- Post #7
- Forum: Introduction
-
F
Guess The Tool
Yes and no lol, specifically designed for one job but you’re correct on the concept of the tool. It’s powersports related Sent from my iPhone using Tapatalk -
F
Guess The Tool
Blue ox, is it a bearing/race or seal driver? Sent from my iPhone using Tapatalk -
F
What new tools have you got lately?
Way better than I thought it would, really need to grab the Tig torch and spool gun for it to try them out! Sent from my iPhone using Tapatalk -
F
What new tools have you got lately?
I got one of these Sent from my iPhone using Tapatalk -
F
Help with a water leak.
My truck that I put @Honky Kong jr’s windshield in was rusted bad in the flange area, I had wholes in it and it was all glued in, had it out and un broken in about 4 minutes, installing it on the other hand without any cable or anything was time consuming and seemed risky but I got it Sent... -
F
Need obscure bearing
Because Kohlers are expensive to fix! Sent from my iPhone using Tapatalk- fmxr47
- Post #9
- Forum: Engine & Performance
-
F
Im a 6.2 Diesel guy
Welcome! My 86 has a 6.5 swapped in! Sent from my iPhone using Tapatalk- fmxr47
- Post #4
- Forum: Introduction
-
F
Door lock knob rod
I was in the same boat and just found one locally on a parts truck Sent from my iPhone using Tapatalk -
F
88-98 Chevys, 99-02 Chevys, and 94-01 Dodges.
My 90 OBS had over 300k miles on it when O got it and I probably put another 60k on it, all I did was valve guide seals and a clutch. Other than that it was all modifications. Oh and a fuel pump relay once. Learned to keep a spare in the glovebox. If it ever happened again. I ended up doing cab...- fmxr47
- Post #84
- Forum: Other Vehicles
-
F
1987 TBI wont start, no spark, but has fuel
Tan! Yes, that rings a bell, I only know it from my 90 OBS which was mounted to the firewall Sent from my iPhone using Tapatalk- fmxr47
- Post #11
- Forum: TBI & EFI Conversions
-
F
1987 TBI wont start, no spark, but has fuel
Don’t forget to unplug the one wire when setting timing, I think it’s white? I really can’t remember. Sent from my iPhone using Tapatalk- fmxr47
- Post #8
- Forum: TBI & EFI Conversions
-
F
Favorite tool brand?
^ precisely... Sent from my iPhone using Tapatalk -
F
Rust repair - order of replacement
I just drive to summit and pickup anything I need [emoji23] Nice being about 35 min away Sent from my iPhone using Tapatalk -
F
Rust repair - order of replacement
Yes, the other ones are called inner rockers for some terrible reason. I used the same as you, they went from corner all the way to A-pillar Sent from my iPhone using Tapatalk -
F
Rust repair - order of replacement
I found no use for the second one, is that what you used? Sent from my iPhone using Tapatalk -
F
Rust repair - order of replacement
Mine was trial and error but all documented in my build thread for he most part, doors will be on and off many times! Also for sure line up your outer rockers after you remove the corners and line up to the door bottom for a good gap! Good luck with a good set of cab corners, the ones I got... -
F
1987 TBI wont start, no spark, but has fuel
I remember having a similar issue on my 90 OBS tbi350 oil pressure sender I thought fixed mine but it’s been a long time ago. Sent from my iPhone using Tapatalk- fmxr47
- Post #5
- Forum: TBI & EFI Conversions
-
F
8.1 4l80e swap
My 6.5td has a 4l80e behind it with zero clearance issues. It has a stand-alone TCI controller which I could adjust the transmissions drive ability with, if I chose to. And this is in an 86 not a newer truck. Sent from my iPhone using Tapatalk- fmxr47
- Post #11
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
F
Toolbox thread
I still have my first box I got when I was a kid from my dad, it was the 3 piece craftsman stack, I sold the little middle section to a friend but I still have the top and bottom. In fact the top is in my company vehicle for when I drive to service calls instead of flying. Sent from my iPhone...
