Search results

  1. nvrenuf

    Big block running hot. Can’t figure out the issue

    With only 2 rows and 1-9/16" core thickness, that looks pretty small.
  2. nvrenuf

    It could have been worse

    There's no splined hub there, the stud flange is part of the axle shaft. You probably had a wheel bearing die and wore into the shaft deep enough that the end broke off. You'll need to check for collateral damage on the housing, brakes, etc but you should be able to buy a new axle shaft, wheel...
  3. nvrenuf

    Big block running hot. Can’t figure out the issue

    I can’t remember if it was discussed, what size radiator was it? Did you order a big replacement unit?
  4. nvrenuf

    Big block running hot. Can’t figure out the issue

    Maybe check the radiator real good for flow. Possibly flush it for good measure? What about belt routing, I've seen serpentine belts that could route differently than intended. Could the belt be driving the water pump in the wrong direction? It would be a last resort since it would be pretty...
  5. nvrenuf

    Big block running hot. Can’t figure out the issue

    What about the radiator, are you sure it’s not blocked internally?
  6. nvrenuf

    Big block running hot. Can’t figure out the issue

    He said it’s a Mark IV block and 781 heads are from the Mark IV era so assuming he used the matching Mark IV head gasket there shouldn’t be any issues.
  7. nvrenuf

    Big block running hot. Can’t figure out the issue

    If there’s no signs of mixing fluids I wouldn’t pull the heads yet. What about the radiator? Is it actually circulating coolant?
  8. nvrenuf

    Should I go bigger u-joints

    I don’t agree with the weak link theory, over build it to begin with and that’s not a problem.
  9. nvrenuf

    Big block running hot. Can’t figure out the issue

    Interesting, I didn’t realize there was interchangeability on the IV vs VI internals. Did you change the fan blade also?
  10. nvrenuf

    Confusing VIN number for 80 pickup

    "TCD14" 4 = pick up
  11. nvrenuf

    Rubber seal(s) on outside of spindle?

    I forgot to say that those kit part numbers I posted will have the 2 seals, the washer and the bearing. There may be a seal only kit available but I’ve never seen it.
  12. nvrenuf

    Rubber seal(s) on outside of spindle?

    Most parts houses carry them. BCA part # 1/2 and 3/4 ton: SBK-1 1 ton: SBK-3
  13. nvrenuf

    Into and identification help !

    My 91 crew cab was a Cheyenne.
  14. nvrenuf

    Into and identification help !

    That sucks, I guess the dash or grill has been replaced? Does the tailgate say Chevy or GMC? Look inside the glove box for an option sticker. I can’t remember the year it changed but it’ll either have a brief description of each option or just a list of 3 digit codes. If it just has codes...
  15. nvrenuf

    Into and identification help !

    Welcome to the site! Look on the passenger side dash trim, there should be a matching emblem there (above the glove box area).
  16. nvrenuf

    Steering arm.for 2" lift help

    You need to go with a stock arm, that raised arm will cause binding problems with the lower lift.
  17. nvrenuf

    Bare Hands

    I wear latex gloves about 50% of the time but definitely always if I’m working with grease or oil. I like for my wife to get her nails and hair done, she looks nice and feels good. I figure I can somewhat reciprocate by not having nasty nails and stained hands.
  18. nvrenuf

    52” front leaf spring setup

    I have 2.5” lift springs but the overload is flat. @Charlie Kleman at some point I’ll add bump stops. I plan to move the bracket forward to center it over the spring plate and space down the bump stop itself.
  19. nvrenuf

    52” front leaf spring setup

    I don’t have bump stops so I left my overloads on to (hopefully) prevent me from over flexing and bending the springs.
  20. nvrenuf

    Old wheel bearing grease cans.

    Those are pretty cool and definitely old. I started working in auto parts in the mid 80's and the cans were already like they are now, sort of a cardboard material.
  21. nvrenuf

    CROSS MEMBER FRAME BROKEN

    @Ricko1966 @bucket is talking about the engine crossmember, cracks at the outboard end are semi common. In fact, they happened enough that GM rivoted a small reinforcement plate on the driver’s side end on 81+ frames. The ORD engine crossmember is a really nice part if the OP wants to replace...
  22. nvrenuf

    Gear Ratio

    Looks like 41/9 which is 4.56. Btw, that gear oil looks NASTY.
  23. nvrenuf

    Should I go bigger u-joints

    I put all 1410’s in my Blazer, fork weak links! lol That said, I ran 1350’s in my old truck with 44’s and never had an issue (4spd and auto).
  24. nvrenuf

    Rear shackle angle

    I’m no suspension expert but it looks ok to me. I’m running 56’s w/ ORD 2.5” shackle flips (swap sides like you) and my shackle angle is similar. My set up hasn’t shown any issues and works well.
  25. nvrenuf

    Mystery Tachometer

    Just to say it, while the factory tachs are super cool I remember mine being slower than aftermarket tachs.

Latest posts

Forum statistics

Threads
44,157
Posts
950,604
Members
36,273
Latest member
dannyphx
Top