Search results

  1. I

    Fleetside tool box...

    50 posts before you can sell anything
  2. I

    Oil pressure sender switch and coolant sender what type of thread sealant to use since your not supposed to use Teflon so it can ground correctly

    ^^^^^^^^^BRYLCREAM ???^^^^^^^^^^^.......I'm OLD
  3. I

    9th Annual Square Body Farm Gathering Richmond In

    @legopnuematic Tell Mom Happy Birthday from us!!!
  4. I

    Show your daily driver

    ^^^^^^^WOW Zach, that's......red^^^^^^^^
  5. I

    Recovery straps remove downed brush/branches/bushes well

    @AuroraGirl ^^^^^^what Shane said!!!!!....lol
  6. I

    New tach conversion kit from usa1 how to mount the tach to the mounting bracket

    Been using my "OLD" nuts for years
  7. I

    1982 C30 looking for 4/6 drop. What did you actually get versus what was advertised?

    OK it's AXLE......... @SquareRoot
  8. I

    C20 vs c10 spindles

    ^^^^^YEP watched my Dad torch my 15 year old Brothers 51 fored 2 dr and set it in the WEEDS!!!!!!^^^^^^^this was out on the farm 8 miles from town.....couldn't wait to go take it to town!!!!!!
  9. I

    1981-82 Metal Lower Tailgate Mldg

    I dunno.. I think maybe ALL of us Square Body owners are crazy^^^^^^^^to a degree....lol
  10. I

    Heat box swap

    ^^^^^^^THIS, there ain't nothing like a Chevy heater^^^^^^^^^
  11. I

    Rear Axel Bearings and Seal

    @SquareRoot ^^^^^^^^
  12. I

    New Courtesy lamp switch is too long to let the door close.

    ^^^^^^THIS @Matt69olds is right!!^^^^^^^^^
  13. I

    Old77’s Oldest Kid’s 1992 S10 Blazer thread

    Never have seen a 12 point AXLE nut, just the tin shield over the real one........learn something new every day
  14. I

    Valve cover bolts won't stay snug.

    ^^^^^^^THIS^^^^^^
  15. I

    Help with difficult problem!!! ‘83 K5/4” lift/NP208 mounting height with incorrect homemade spacers vs correct spacers???

    Don't think I've seen 1/2 inch bolt for a crossmember??? 3/8 maybe 7/16??
  16. I

    I got a lift

    ^^^^^What brand of midrise? I have a BendPak 6000 lb drive over for my alignment work. Total lift is almost 4 feet. Plus my 2 post.^^^^^
  17. I

    Crack/Knick in 350 Cylinder Wall

    You are gonna have to do some of your own homework, shop prices vary through out the land
  18. I

    Confusing info on tightening spindle lock nuts

    Have ALWAYS put some wheel bearing grease on dry tapered bearings in my FF rear axle when I had the hubs off. NOT packed, but NOT dry.......have NEVER had a problem, with the bearing grease, it doesn't drip off.
  19. I

    What have you done to your square lately??

    ^^^^^^^^^Just like the song said "It's 5 o'clock somewhere"^^^^^^^^^^
  20. I

    Header swap begins.

    LONG sleeves and DUCT tape!!!!!!!!!!
  21. I

    AC system identification

    Those worm gear clamps with the keeper are/were standard on my 66 ChevyII original A/C car. Looks like a Sanden 508 compressor, just what I have on said ChevyII
  22. I

    Leaf Spring Install Advice - Won't line up, shackle angle

    In the future a "come along" would be your friend, for pulling that AXLE back into place...............ATTENTION Spelling police!!!!! @SquareRoot
  23. I

    Header swap begins.

    The sleeves on the front disc brake calipers are just about the right size??
  24. I

    New carb starts then dies after 5 seconds

    Pumping the pedal???^^^^^^^^^
  25. I

    Death wobble, or bad wheel balance?

    I don't think you can balance new tires properly. I believe that the tires need to "seat" on the wheels before they are are totally on? I always rebalance 400 to 500 miles after they are installed...........just my experience......That and $3 may buy you a cup of coffee........or a beer...lol

Latest posts

Forum statistics

Threads
44,157
Posts
950,597
Members
36,272
Latest member
armchair
Top