Search results

  1. Craig Nedrow

    Broken hearted kid and fuel system

    James, lots of good advice here, but lots of jumping around. Start at the source, the tank first. Disconnect the fuel line at the selector valve under the truck, gas should run out, lots of gas. If not, there is the problem, it's plugged. Just try that first and see what happens. If lots of gas...
  2. Craig Nedrow

    Windshield installation

    Man! That’s not what I wanted to hear my back window works fine just doesn’t have any of the rubber pieces in it. I was thinking of replacing it maybe I’ll just leave it.
  3. Craig Nedrow

    Saddle tank delete with carburation

    Pictures? What I just finished for my good wife.
  4. Craig Nedrow

    Turning off weird

    Rusty is right, to advanced on the timing
  5. Craig Nedrow

    Differential skid plates

    Are you sure it is a Dana, and not a 10 bolt Chevy.? Dana 44 under 3/4 ton, like k20. My k20 is Dana, my k10 is chevy
  6. Craig Nedrow

    Looking where to buy axels

    Randy’s worldwide, excellent stuff go here: https://www.randysworldwide.com/shop/za-g14071750
  7. Craig Nedrow

    Rear Main Seal

    Lucas has worked for me
  8. Craig Nedrow

    Differential skid plates

    I thought that the K10 had 12 bolt rear and ten bolt front. Anyway mine does. Diff cover on my d60 is an LPW, not cheap, but that rear is not in my k10.
  9. Craig Nedrow

    Saddle tank delete with carburation

    Eric, you gonna swap the 454 this winter? Your gonna love that. What is the motor out of?
  10. Craig Nedrow

    Cucv M1008 introduction/build, hello I'm new here.

    Just saw that swap this week, guy bought a 4 wheeler from me, and he swapped in the Caddy, and Hydra boost. He has a fabrication business, and uses it for that. He loves it. Welcome!
  11. Craig Nedrow

    Wireing help please

    White wire goes in the dist, right side of cap, in the front I believe. There is a slot for Tach there too.
  12. Craig Nedrow

    SBC Cylinder Head Decision

    I really like AFR, cause the parts they use are top of the line, Ferrea valves, Pac springs, often Titanium retainers. My K20 lives in the Cascades Wa ST, has had a circle track motor Crower cam on a 107 LSA, fair amt of overlap, knurly sounding, close to .500 lift, haul ass on the street. I...
  13. Craig Nedrow

    Changing brake fluid

    I use the same exact method as WFO, except that I use a mighty vac, as most of the time I am alone in the shop. Do the longest run first and progress to the shortest, usually RR,LR,RF,LF. Don't run it dry, or you get to do it again.
  14. Craig Nedrow

    I need to drill and tap Vortec 350 missing timing cover bolt holes. Help with size!!

    Jon been a machinist 40 years and still machining, Like Eric said above. #7=.201, 13/64=.203. Could write a dissertation on tapping, but really Rick is telling you the truth. Leave it alone. Drilling cast, and tapping is no real mystery, but if the block came that way, I would leave it alone.
  15. Craig Nedrow

    Spark, Fuel, Crank but won't start

    Hey Matt, don't mind Rusty, you'll get used to him, and Rusty is ......amusing to say the least.
  16. Craig Nedrow

    Saddle tank delete with carburation

    I remember our old power wagon gas tank was under the bed (flat bed) outside of the frame just a square tank. Seems like the square body tanks would work,
  17. Craig Nedrow

    Keep Manual shift for the LS or swap in an auto?

    I have a 465 in the International 1600 loadster, rebuilt it a couple times, old tech, parts are getting scarce, no OD. I will build my 454 with a 4l80e, and 6.0 LQ4 which came with a 4l80e. I love to shift too, but not truck trans. Muncie, t5, t56, all ok, but will need pretty expensive parts to...
  18. Craig Nedrow

    Bonneville 2023 Sept. 8-10

    We may take this car, just finished it, and runs good, but need carb kit and tuned. Bugger VW's, wife loves it, it is a real different deal to work on.They have a 36hp challenge down there, and there are some fast VW's, motors cost more thar my fofiddyfo. 6.2 diesel, almost done, get it...
  19. Craig Nedrow

    Bonneville 2023 Sept. 8-10

    Actually three out of two have been canceled. Well SPREAD THE WORD EVERYONE THAT READS THIS!!!! I have stayed in Motel, tented, RVed, preferer to stay out on the salt. The days can be warm, I take my umbrella, Morell hat, some way to get around, water, jerkey, ice chest. At night because it is...
  20. Craig Nedrow

    350 to 400 swap... Worth it?

    454, lost the tire on this burnout.
  21. Craig Nedrow

    Brand and Ratio for Ring and Pinion Gears?

    Ah Harry Bugger the Shop cat, and aspiring square body owner.
  22. Craig Nedrow

    350 to 400 swap... Worth it?

    Mark Jones is on here, builds excellent engines, Mark @ Vortec Pro.
  23. Craig Nedrow

    350 to 400 swap... Worth it?

    Ah yes the debate, my 355 circle track motor (9.5:1) in a K20, sounds awesome, mean, 454 8:1 compression [email protected] cam, headers, intake, (350 the same) sound tame, spanks that 355. Used both for towing, 355 higher rpm shifts, 454, shift whenever, always plenty of torque. Love the 355, love the...
  24. Craig Nedrow

    Pulling Sucks--2001 Suburban 3/4 ton--6.0

    We have a 21.5 Grand Imagine, pulled with our 2018 GMC 6.2. Mileage is consistent 9, pulls good. The 6.0 is an awesome engine. Have it tuned, (I use HP tuners). Small cam, (230 @ .05) around .600 life, 107-110 LSA. I also love the 454, tows anything.
  25. Craig Nedrow

    Brand and Ratio for Ring and Pinion Gears?

    I used Yukon in a D60, excellent. Also used other Yukon parts, very good stuff. I also use Strange engineering, top of the line. I bought a good set of pinion tools, and yes you can do it, it is a learning curve, and first time you will question your stupidly in doing it. But here the thing, you...

Latest posts

Forum statistics

Threads
44,157
Posts
950,562
Members
36,268
Latest member
JUKA
Top