Let’s slay this dragon…

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Jgonick

Jgonick

Full Access Member
Joined
Jan 12, 2017
Posts
328
Reaction score
414
Location
West Texas
First Name
Joel
Truck Year
1985
Truck Model
K10
Engine Size
350
wildgoose said:
Should both door switches have 2 wires connected to the switch? Driver side had 2 but passenger side only 1.
Click to expand...
White wire is ground- both sides should have one. Tan wire is for key left in ign ground (warning ding) - only on driver side.
 
Jgonick

Jgonick

Full Access Member
Joined
Jan 12, 2017
Posts
328
Reaction score
414
Location
West Texas
First Name
Joel
Truck Year
1985
Truck Model
K10
Engine Size
350
fast 99 said:
Likely a broken wire under carpet drivers side.
Click to expand...
Orange wire is taking power to dome light. White wire is ground coming back- it is spliced somewhere slightly above the fuse box with the white wire running to door jamb & to courtesy light. From courtesy light the white wire (sometimes changes to wht/blk) runs to light switch to ground it when you twist the pull knob.

The orange wire (I marked in attachment) coming out of the fuse box should meet up with the white wire and head back down under the carpet.(also marked on attachment)

So if your courtesy light is working- it gives you an idea where the problem might be. Like @fast 99 mentioned- very common for it to be broken under the carpet.
 

Attachments

  • IMG_4002.jpeg
    IMG_4002.jpeg
    198.3 KB · Views: 23
Last edited:
A

ajdouble

Junior Member
Joined
Oct 23, 2024
Posts
5
Reaction score
5
Location
somewhere in texas
First Name
mark
Truck Year
1979
Truck Model
1500/c10
Engine Size
250
The circuit has to be complete for the light to burn. if schematic is not helping try working from the receptacle to the point of power. broke wire makes sense. Ohms law comes to mind.
 
wildgoose

wildgoose

Full Access Member
Joined
Oct 6, 2023
Posts
52
Reaction score
127
Location
Waxhaw, NC
First Name
Michael
Truck Year
1984
Truck Model
K2500
Engine Size
454
Jgonick said:
Orange wire is taking power to dome light. White wire is ground coming back- it is spliced somewhere slightly above the fuse box with the white wire running to door jamb & to courtesy light. From courtesy light the white wire (sometimes changes to wht/blk) runs to light switch to ground it when you twist the pull knob.

The orange wire (I marked in attachment) coming out of the fuse box should meet up with the white wire and head back down under the carpet.(also marked on attachment)

So if your courtesy light is working- it gives you an idea where the problem might be. Like @fast 99 mentioned- very common for it to be broken under the carpet.
Click to expand...
Thanks. The white wire from that orange/white pair does in fact run behind the fuse box to above. I can’t see where it goes but assume either the door switch or it’s open ended. There are no courtesy lights installed in this truck.

I also noticed in the owner manual that the clock and dome light is on the same fuse so pulling that fuse today to check it before I pull out seats and carpet.
 
Jgonick

Jgonick

Full Access Member
Joined
Jan 12, 2017
Posts
328
Reaction score
414
Location
West Texas
First Name
Joel
Truck Year
1985
Truck Model
K10
Engine Size
350
wildgoose said:
I pull out seats and carpet
Click to expand...
You shouldn't need to pull out seats. It will run down the side by the driver's door. Usually taking the plastic piece off the lower door jamb is all you need to do to peel back the carpet to see.
 
Last edited:
S

Steelbuddha

Junior Member
Joined
Mar 16, 2024
Posts
29
Reaction score
25
Location
Central North Carolina
First Name
Jonathan
Truck Year
1984
Truck Model
K20 (dump bed)
Engine Size
350
This is the Painless Wiring manual for their big-ass 27-circuit harness. It's an excellent reference and explains a lot of stuff: https://painlessperformance.com/wp-content/uploads/2024/02/90627.pdf The color codes are all consistent with original.

I installed one of these in my 1984 K-20 and all electrical problems disappeared.

Re: your question about the green wire, are your reverse lights working?
 
O

olnick

Full Access Member
Joined
Feb 7, 2019
Posts
53
Reaction score
33
Location
Milford NH
First Name
Nick
Truck Year
1978
Truck Model
c15
Engine Size
1982 350 4 bolt mains
here is a wiring diagram:
www.mediafire.com

X8430_1984_GMC_CK_Light_Duty_Trucks_Wiring_Manual

MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com

I have used this site for at least 10 years now all the downloads are OEM manuals
This will get you out of trouble!!
 
wildgoose

wildgoose

Full Access Member
Joined
Oct 6, 2023
Posts
52
Reaction score
127
Location
Waxhaw, NC
First Name
Michael
Truck Year
1984
Truck Model
K2500
Engine Size
454
Alright, alright, alright… on today’s episode of “sh!t you can’t make up” I decided to remove all of the upside down or blown fuses with those nifty blow glows. Figured since the battery is at least 3 years old, may as well pick up a new one. Good to go, right?

What are the frickin’ chances… my voltmeter gauges is now reading 8 volts during the drive home. Cause I was really wanting to stay up and install a battery late at night.

New battery installed. Volt gauge reads 10 with key in the on position. Is that a normal value? Old batt measured 12.3VDC with a meter on the bench and new is 12.6.
 
Last edited:
ali_c20

ali_c20

Full Access Member
Joined
Sep 20, 2016
Posts
1,348
Reaction score
1,953
Location
Austria
First Name
Alexander
Truck Year
1974, 1979
Truck Model
C20, K5
Engine Size
350, 350
I throw in Volt gauge ground.
 
wildgoose

wildgoose

Full Access Member
Joined
Oct 6, 2023
Posts
52
Reaction score
127
Location
Waxhaw, NC
First Name
Michael
Truck Year
1984
Truck Model
K2500
Engine Size
454
ali_c20 said:
I throw in Volt gauge ground.
Click to expand...
I might agree with you but I should’ve said it was reading 8 volts but also varying up and down with acceleration and dropping below 8 with window switches operating.
 
wildgoose

wildgoose

Full Access Member
Joined
Oct 6, 2023
Posts
52
Reaction score
127
Location
Waxhaw, NC
First Name
Michael
Truck Year
1984
Truck Model
K2500
Engine Size
454
Update… alternator was only outputting 11 volts after the new battery was installed. Should’ve known this would turn into a two for one special. New alternator going in now. Just finished priming and painting the thru bolt bracket since it was covered in grease/dust.

As an added bonus… the plastic wire loom that was covering the alternator harness melted to the intake manifold, directly on the EGR blanking plate. The plate cracked near the thru hole so some steel stick putty is nearly cured to drill and reinstall that little widget. Explains the truck sounding and running like crap the last few days.

Fun times.
 
wildgoose

wildgoose

Full Access Member
Joined
Oct 6, 2023
Posts
52
Reaction score
127
Location
Waxhaw, NC
First Name
Michael
Truck Year
1984
Truck Model
K2500
Engine Size
454
Alright so finally got back to one of the original objectives… the pesky dome light. I traced the wire under the driver side carpet. Found no cut wires (but did find some spot rust) and cleaned the connector behind the speaker. After reconnecting, I tested and got 12 volts at the wire before the speaker box. So power is somehow finally making it to the light. Cool. Inserted a bulb and the light worked. The passenger side door switch grounded properly and the light went out. However, shouldn’t the light have stayed on if the driver door is open?
 
wildgoose

wildgoose

Full Access Member
Joined
Oct 6, 2023
Posts
52
Reaction score
127
Location
Waxhaw, NC
First Name
Michael
Truck Year
1984
Truck Model
K2500
Engine Size
454
Further… the dome light also works now when the headlight knob is rotated full left and past the click, but it still won’t turn off when the switch is depressed. Switch tested good for continuity, as expected since it’s brand new.
 
wildgoose

wildgoose

Full Access Member
Joined
Oct 6, 2023
Posts
52
Reaction score
127
Location
Waxhaw, NC
First Name
Michael
Truck Year
1984
Truck Model
K2500
Engine Size
454
These are the wires coming through the door switch hole. White wire is carrying 12V. Brown wire has nothing and fails continuity test. I can’t tell where it goes after the door. There is a similar brown wire going from fuse panel to the left side fuel tank but I’m assuming I’ve followed the wrong wire during my tracing.
You must be registered for see images attach
 
You must log in or register to reply here.

Similar threads

RanchWelder
Ice Cube Fuse Fail
2
Replies
20
Views
2K
haxored
haxored
bigcountry78
2001 Silverado advice
2
Replies
25
Views
1K
AuroraGirl
AuroraGirl
RanchWelder
Electrical dash wiring / wire color issues.
Replies
6
Views
2K
RanchWelder
RanchWelder
T
Not using factory fuse box after engine swap, lighting wiring with column and ignition switch problems.
Replies
5
Views
2K
Matt69olds
Matt69olds
Haydenh
Headlights on= No Turns, Headlights off= Turns
2
Replies
15
Views
3K
Scottgenex
S

Latest posts

Forum statistics

Threads
44,419
Posts
957,232
Members
36,758
Latest member
PapaD
Top