Let’s slay this dragon…

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

wildgoose

wildgoose

Full Access Member
Joined
Oct 6, 2023
Posts
52
Reaction score
127
Location
Waxhaw, NC
First Name
Michael
Truck Year
1984
Truck Model
K2500
Engine Size
454
Happy Thanksgiving yall… had a minute in between turkey and football to snap a few photos of my fuse box. This truck is an 84 diesel that has been swapped to a 454.

1. Anything y’all see obvious that needs to be addressed/corrected?

2. Any idea what the broken green wire with the black plastic fuse holder looking thing went to?

3. Dome light will not turn on… switches and bulb have been replaced. Still nothing.

4. I want to add a dedicated USB power panel in the cabin. Any recommendations on where to tap for power or go all the way to the battery?

5. What could be extra/not needed and likely can be removed?

Thanks yall

You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
You must be registered for see images attach
 
Last edited:
wildgoose

wildgoose

Full Access Member
Joined
Oct 6, 2023
Posts
52
Reaction score
127
Location
Waxhaw, NC
First Name
Michael
Truck Year
1984
Truck Model
K2500
Engine Size
454
Snipped a zip tie and was able to make some progress in removing a few wires that weren’t terminated on either end so figured nothing can die that wasn’t already dead.

Also disconnected the horn as someone had removed it from the steering wheel and relocated it to a button under the dash… I can go without a horn for a while for the sake of clarity.

A bit easier to see what lives in here now…

You must be registered for see images attach
You must be registered for see images attach
 
SquareRoot

SquareRoot

Full Access Member
Joined
Mar 18, 2017
Posts
4,230
Reaction score
8,123
Location
Arizona
First Name
Mike
Truck Year
85
Truck Model
K20
Engine Size
350
Looks like spaghetti has replaced the traditional turkey meal? You can get a wiring schematic from LMC for cheap. It's worth it.
 
Dmack

Dmack

Full Access Member
Joined
Mar 13, 2019
Posts
342
Reaction score
449
Location
Central OR
First Name
Dave
Truck Year
1983
Truck Model
K20
Engine Size
350
Hate to state the obvious, but you will probably just have to start tracing wires to.see where they go. You will probably find one of the added wires will go to the HEI, since it wouldn't have that provision on a diesel.

My 83 also was a diesel to gas conversion. Mine was such a mess, I went to a junkyard and pulled a complete harness out of a gas square.
 
R

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,596
Reaction score
9,112
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
Okay for the guys doing gas swaps into diesels. Use the injection pump solenoid wire to control the ignition. Disregard/delete the glow plug wiring. All the other under hood wiring you need is all there and straight forward. Alternator,gauges,starter,air-conditioning.
 
Last edited:
wildgoose

wildgoose

Full Access Member
Joined
Oct 6, 2023
Posts
52
Reaction score
127
Location
Waxhaw, NC
First Name
Michael
Truck Year
1984
Truck Model
K2500
Engine Size
454
SquareRoot said:
Looks like spaghetti has replaced the traditional turkey meal? You can get a wiring schematic from LMC for cheap. It's worth it.
Click to expand...
Is it just the same schematic in the wiring manual printed out?
 
wildgoose

wildgoose

Full Access Member
Joined
Oct 6, 2023
Posts
52
Reaction score
127
Location
Waxhaw, NC
First Name
Michael
Truck Year
1984
Truck Model
K2500
Engine Size
454
Dmack said:
Hate to state the obvious, but you will probably just have to start tracing wires to.see where they go. You will probably find one of the added wires will go to the HEI, since it wouldn't have that provision on a diesel.

My 83 also was a diesel to gas conversion. Mine was such a mess, I went to a junkyard and pulled a complete harness out of a gas square.
Click to expand...
I get it… there will always be a tracing job. No doubt I’ll have to track down where a lot of these go. But being new to these trucks, just hoping some of y’all might see something obvious and either point it out or make a recommendation.

Good idea… I need to find a junkyard around here that has a few trucks and see what I can find.
 
fast 99

fast 99

Full Access Member
Joined
Dec 31, 2021
Posts
2,090
Reaction score
3,065
Location
Spokane, Washington
First Name
Brian
Truck Year
81,85
Truck Model
K20
Engine Size
350
Any wire with a crimp on connector is not factory, such as the yellow wire near the flasher. Not saying that is all bad just trace it down. If not deleted make sure whatever it is powering doesn't overload that circuit.
 
SquareRoot

SquareRoot

Full Access Member
Joined
Mar 18, 2017
Posts
4,230
Reaction score
8,123
Location
Arizona
First Name
Mike
Truck Year
85
Truck Model
K20
Engine Size
350
wildgoose said:
Is it just the same schematic in the wiring manual printed out?
Click to expand...
I'm not sure what the "wiring manual" looks like. It does show every circuit for all available options gas or diesel. I find it much easier to decipher on big 14 x 20 inch paper rather than on a screen.
 
wildgoose

wildgoose

Full Access Member
Joined
Oct 6, 2023
Posts
52
Reaction score
127
Location
Waxhaw, NC
First Name
Michael
Truck Year
1984
Truck Model
K2500
Engine Size
454
fast 99 said:
Any wire with a crimp on connector is not factory, such as the yellow wire near the flasher. Not saying that is all bad just trace it down. If not deleted make sure whatever it is powering doesn't overload that circuit.
Click to expand...
Thanks!! Yeah that one is probably the first one I’m going to trace.

Also concerned about the fuses that a lower amp rating than what the fuse block is labeled.
 
R

Ricko1966

Full Access Member
Joined
Apr 11, 2017
Posts
5,596
Reaction score
9,112
Location
kansas
First Name
Rick
Truck Year
1975
Truck Model
c20
Engine Size
350
wildgoose said:
Thanks!! Yeah that one is probably the first one I’m going to trace.

Also concerned about the fuses that a lower amp rating than what the fuse block is labeled.
Click to expand...
I wouldn't worry about an amp rating too low,worst case it pops the fuse and you replace it with the correct fuse. Too high and you can fry wires or components.
 
Last edited:
fast 99

fast 99

Full Access Member
Joined
Dec 31, 2021
Posts
2,090
Reaction score
3,065
Location
Spokane, Washington
First Name
Brian
Truck Year
81,85
Truck Model
K20
Engine Size
350
Dome light has power standing one side of bulb, switches ground. Likely a broken wire under carpet drivers side.
 
wildgoose

wildgoose

Full Access Member
Joined
Oct 6, 2023
Posts
52
Reaction score
127
Location
Waxhaw, NC
First Name
Michael
Truck Year
1984
Truck Model
K2500
Engine Size
454
fast 99 said:
Dome light has power standing one side of bulb, switches ground. Likely a broken wire under carpet drivers side.
Click to expand...
Should both door switches have 2 wires connected to the switch? Driver side had 2 but passenger side only 1.
 
You must log in or register to reply here.

Similar threads

RanchWelder
Ice Cube Fuse Fail
2
Replies
20
Views
2K
haxored
haxored
bigcountry78
2001 Silverado advice
2
Replies
25
Views
1K
AuroraGirl
AuroraGirl
RanchWelder
Electrical dash wiring / wire color issues.
Replies
6
Views
2K
RanchWelder
RanchWelder
T
Not using factory fuse box after engine swap, lighting wiring with column and ignition switch problems.
Replies
5
Views
2K
Matt69olds
Matt69olds
Haydenh
Headlights on= No Turns, Headlights off= Turns
2
Replies
15
Views
3K
Scottgenex
S

Latest posts

Forum statistics

Threads
44,414
Posts
957,001
Members
36,738
Latest member
Tjreid
Top